Processor & Main-memory

• Powerful 32-bit ST ARM7 processor.
• 1088 KB fast execution RAM.
• 2304 KB Flash for firmware/application.

Storage

• 3.5 MB persistent data flash.
• 4 MB internal FAT32 flash drive.
• 1 MB circular automatic datalogger.
• 8 KB Virtual FRAM with fast access / unlimited write endurance.
• Micro SD-CARD reader. Up to 32 GB.

GSM

• Quad-band GSM engine. 850/900/1800/1900 MHz.
• GPRS Class B, Multislot 10.
• CSD with up to 19 Kbps.
• SMS / PDU.
• Micro-SIM 1.8/3 volt.
• Optional Gemalto SIM-on-chip.
• Delivered with ’thumb’ antenna.

SuperGPS

• Mediatek MT3329 Single Chip.
• 66 acquisition / 22 tracking channels.
• SBAS (WAAS,EGNOS,MSAS).
• Prepared for A-GPS.
• Position update with up to 4 hz.
• Sensitivity. Tracking: -165 dBm Reacquisition: -160 dBm Cold start: -148 dBm.
• Accuracy: < 2.5m CEP.
• Active 3 volt GNSS antenna.
• Delivered with a tiny magnet antenna with 2 meter cable.

Battery and Charger

• On-board 900mA (nom.) Li-Ion battery.
• Intelligent charger with temperature throttle and sub-zero degrees support.
• On-board temperature sensor.

Electrical Specification

• Operating voltage is 8 to 36 VDC.
• Short and reverse power protected.

Digital/Analog Interface

• 2 x digital solid-state digital output.
  Max. 36 volt / 0.75 A per. channel.
  Short-circuit, ESD, Inductive kick-back protected up to 20 mH.
• 2 x digital inputs.
  Logic high: 8 to 40 VDC.
  Logic low: -5 to 3 VDC.
• Digital input #1 can be used as ignition.
• 1 x analog input.
  Range is 0..10V.
  Resolution: 10 bit
  Precision: ±1.5% FSR @ 25°C

Communication

• Warp-c: Full CAN2.0B with hardware filtering and multi-speed support.
• Warp: RS232 and 1-Wire bus.
• On-board 868 Mhz ISM RF Up to 15 meter indoor / Up to 50 meter outdoor.

Power Management

• 5 execution speeds.
• Wait for Event: Timer, Digital input, RS232, CAN, GSM, Accelerometer and power change state.
• Wait for event, from: 600 uA@12V.
• Supervision of supply voltage / type.

Accelerometer

• 3-axis digital acceleormeter.
• Resolution: 12 bit @ ±16g.
• Low-power mode.

Internal Interface

• Mini-USB connector for service port.
• SIM-card slot for micro-SIM.
• Micro SD-CARD slot.
• Reset/recovery switch.

External Interface

• 2 x bi-color LED indicators.
• Yellow LED for status.
• SMA female connector for GSM antenna.
• SMA female connector for GPS antenna.

On-Demand Hardware Options

• Applied ”any-time” - locally or remotely.
• Over-the-air hardware upgrade.

Physical Characteristics

• Encapsulation: Black UL94 plastic.
• Sealing membrane.
• 50 cm open-ended interface cable.
• Approx. 250 gram without accessories.
• W 92 x H 30 x D 58 mm. (without mounting flanges).

Environmental Specification

• Operating temperature: -30 to 55°C.
• Battery charge temperature: -10 to 45 °C
• Recommended storage temperature: 0 to 45 °C.
• Humidity: 5..90% (non condensing).
• IP-66 ingress protected.

Approvals

• E1 type approval: 2004/104/EC UN ECE R10.
• CE mark / Applied R&TTE directive.
• GSM Engine: CE/GCF/FCC/PTCRB.

Warranty

• Two-years return to factory parts and labor.
• Optional warranty up to 5 years. (restrictions apply).

Extensive Standard Features

• Internal 4 MB FAT32 flash drive.
• 1 x RS232 channel.
• 2 x analog inputs with 0..10 volt / 12 bit precision.
• 5 x digital inputs and 4 high-power solid-state digital outputs.
• 1-Wire bus for accessories such as ID-button reader, temperature sensors, etc.
• Powerful on-demand hardware options:
  • Full CAN 2.0B controller with hardware filtering and multi-speed support.
  • RS485 channel with MODBUS and expandable I/O.
  • Internal SIM-card reader. Active reader selectable from the application.
• On-demand options can be applied anytime - even remotely after installation.
• Wide operating range from 8..36 VDC.
• External power can be selectable enabled/disabled by the application.
• On-board high-capacity Li-Ion battery.
• Advanced power-management with wake-up on a wide range of events.
• High-speed USB programming cable support.
• Fully supported by the VikMote Gateway 2 and the VikMote Deployment Server.
• Exclusive and durable aluminum encapsulation.

Platform Advantages

• NX32 execution architecture.
• Free VikMote Tools.
• Programmable in VPL and Lua.
• Huge standard API.
• Comprehensive protocol support.
• Full featured Device Simulator.
• Sophisticated deployment tools.
• Backward and forward compatible.

Device Advantages

• Quad band GSM engine.
• Multi-GNSS positioning engine.
• Internal FAT32 flash-drive.
• Internal and external SIM reader.
• 3-axis accelerometer.
• Full CAN 2.0B support.
• 1-Wire bus.
• RS232 and RS485 channels.
• Digital and analog I/O.
• Digitized voice playback.
• DTMF decoding/transmission.
• High-capacity battery.
• State of the art power-management.
• On-demand hardware options.

Deployment Features

• Full Vikingegaarden / Upgrade & Deployment server compatible.
• Upgrade of application, firmware and parameters over CSD, GPRS and Cable.
• Upgrade can occur during full unit operation minimizing the impact on the customer.
• Unattended and fully automatic upgrade and deployment.
• Automatic ”bootstrap” of un-programmed unit on first time installation.

Cloud-based system

• Web-based system with internet access from any PC, Mobile phone or tablet.
• Modular system.
• Own VMS domain.
  • Online setup.
  • Here-and-now status display.
  • Alarm List in real time.
  • Backup Settings.
  • No subscription - no binding.
  • Data usage per. year about 12-14 Mb.
• Time stamps.
• Multi user system.
• Webservice.

High Performance

• Based on the VikMote M2M Platform.
• Cost-efficient variant of the VX20 TURBO.
• NX32 execution architecture.
  • VikMote tools with full featured device simulator.
  • Huge standard API with more than 800+ functions.
  • Comprehensive protocol support, including: TCP-UDP/IP, FTP, SMTP, RACP, MQTT, MODBUS, FMS/J1939, NMP/Garmin FMI.
  • Fully backward compatibility with existing X32 applications.
• World-wide Quad-band GSM engine.
• External SIM-card reader.
• Digitized audio can be played over GSM or to an external device.
• DTMF support for implementation of Interactive Voice Response applications.
• State-of-the art Multi-GNSS positioning engine with GPS,GLONASS,QZSS.
• High-performance 3-axis accelerometer with 16g scale.
• Enhanced memory sub-system with fast program execution.
• Huge data-flash/logger memory with a capacity of 4.5 MB.

Processor and Main-memory

• Powerful 32-bit ST ARM7 processor.
• 2112 KB fast execution RAM.
• 4532 KB Flash for firmware/application.

Storage

• 3.5 MB persistent data flash.
• 4 MB internal FAT32 flash drive.
• 1 MB circular automatic datalogger.
• 20 KB FRAM with fast access / unlimited write endurance.

GSM

• 850/900/1800/1900 Mhz.
• GPRS Multi-slot class 12.
• Max. 85.6 kbps (up/down link)
• CSD with up to 14.4 Kbps.
• SMS / PDU.
• DTMF decoding / transmission.
• Digitized voice playback / IVR.
• Micro-SIM 1.8/3 volt.
• External and internal SIM card-reader.
• Switchable from the application.

GNSS / GPS

• Mediatek MT3333 Multi-GNSS chip.
• GPS, GLONASS and QZSS.
•  99 acquisition / 33 tracking channels.
• SBAS (WAAS ,EGNOS, MSAS, GAGAN).
• Position update with up to 4 hz.
• A-GPS capable.
• Sensitivity. Tracking: -165 dBm Reacquisition: -160 dBm Cold start: -148 dBm.
• Accuracy: < 2.5m CEP.
• Anti-jamming, Noise cancellation.
• Active 3 volt GNSS antenna.

Electrical Specification.

• Operating voltage is 8 to 36 VDC.
• Short and reverse power protected.

Battery and Charger

• On-board 2Ah (nominal) Li-Ion battery.
• Intelligent charger with temperature throttle and sub-zero degrees support.
• On-board temperature sensor.

Digital/Analog Interface

• 4 x digital solid-state digital output. Max. 36 volt / 1.5 A per. channel.
• Short-circuit, ESD, Inductive kick-back protected up to 20 mH.
• 5 x digital inputs. Logic high: 8 to 40 VDC. Logic low: -5 to 3 VDC.
• Digital input #5 can be used as ignition.
• 2 x analog inputs. Range is 0..10V. Resolution: 12 bit Precision: ±1.5% FSR @ 25°C
• Protected against transients and low-pass filtered.
• Expandable I/O with MODBUS.

Communication

• Full CAN2.0B with hardware filtering and multi-speed support.
• 1 x RS232 with RX/TX. Alternatively used as service port.
• 1 x RS485 with MODBUS support.
• 1-Wire bus.

Power Management

• 5 execution speeds.
• Wait for Event: Timer, Digital input, RS232, CAN, GSM, Accelerometer and power change state.
• Wait for event, from: 300 uA@12V.
• Supervision of supply voltage.
• Disable external power.

Accelerometer

• 3-axis digital acceleormeter.
• Resolution: 12 bit @ ±16g.
• Low-power mode.

On-Demand Hardware Options

• Applied ”any-time” - locally or remotely.
• Over-the-air hardware upgrade.

External Interfaces

• SIM-card slot for micro-SIM with lock and presence detection.
• 4 x LED indicators.
• Reset/recovery switch
• TE-Connectivity ”Mate’n’Lock’: RS232, I/O, Power, Communicaton.
• SMA Female connector for GSM.

Physical Characteristics

• Encapsulation: Aluminum/plastic.
• Optional mounting bracket.
• Approx. 290 gram without accessories.
• W 97 x H 35 x D 132 mm. (without antenna connectors).

Environmental Specification

• Operating temperature: -35 to 60°C.
• Battery charge temperature: -10 to 45 °C
• Recommended storage temperature: 0 to 45°C.
• Humidity: 5..90% (non condensing).
• IP30 with SIM/Connectors in use.

Approvals

•  E1 type approval: 2004/104/EC UN ECE R10 - ed 3.
• CE mark / Applied R&TTE directive.
•  GSM engine: CE/GCF/FCC/PTCRB.

Warranty

• Two-years return to factory parts and labor.
• Optional warranty up to 5 years. (restrictions apply).

Extensive Standard Features

• Internal 8 MB FAT32 flash drive.
• Standard FAT32 SD-CARD reader with up to 32 GB capacity.
• 2 x RS232 channels and 1 x RS485 channel.
• 2 x analog inputs with 0..10 volt / 12 bit precision.
• 5 x digital inputs and 4 high-power solid-state digital outputs.
• Full CAN 2.0B controller with hardware filtering and multi-speed support.
• 1-Wire bus for accessories such as ID-button reader, temperature sensors, etc.
• Wide operating range from 8..36 VDC.
• External power can be selectable enabled/disabled by the application.
• On-board high-capacity Li-Ion battery.
• Advanced power-management with wake-up on a wide range of events.
• Hands-free interface with microphone and Class-D audio speaker amplifier.
• High-speed USB programming cable support.
• Fully supports the Professional Navigation and Messaging device PNM-220.
• Support the Garmin Fleet Management Interface.
• Fully supported by the VikMote Gateway 2 and the VikMote Deployment Server.
• Accessories: Wi-Fi, Ethernet, Bluetooth, Camera and PNM-220 Navigation Device.
• Exclusive and durable GOLD aluminum encapsulation.
• Find out more and start developing today!

Platform Advantages

• NX32 execution architecture.
• Free VikMote Tools.
• Programmable in VPL and Lua.
• Huge standard API.
• Comprehensive protocol support.
• Full featured Device Simulator.
• Sophisticated deployment tools.
• Backward and forward compatible.

Deployment Features

• Full Vikingegaarden / Upgrade & Deployment server compatible.
• Upgrade of application, firmware and parameters over CSD, GPRS and Cable.
• Upgrade can occur during full unit operation minimizing the impact on the customer.
• Unattended and fully automatic upgrade and deployment.
• Automatic ”bootstrap” of un-programmed unit on first time installation.

Cloud-based system

• Web-based system with internet access from any PC, Mobile phone or tablet.
• Modular system.
• Own VMS domain.
  • Online setup.
  • Here-and-now status display.
  • Alarm List in real time.
  • Backup Settings.
  • No subscription - no binding.
  • Data usage per. year about 12-14 Mb.
• Time stamps.
• Multi user system.
• Webservice.

High Performance

• Based on the VikMote M2M Platform.
• NX32 execution architecture.
  • VikMote tools with full featured device simulator.
  • Huge standard API with more than 800+ functions.
  • Comprehensive protocol support, including: TCP-UDP/IP, FTP, SMTP, RACP, MQTT, MODBUS, FMS/J1939, NMP/Garmin FMI.
  • Fully backward compatibility with existing X32 applications.
• High-speed 3G/HSDPA GSM engine. Backward compatible with 2G/2.5G.
• Internal and external SIM-card reader selectable from the application.
• Digitized audio can be played over GSM or to an external device.
• DTMF support for implementation of Interactive Voice Response applications.
• State-of-the art Multi-GNSS positioning engine with GPS,GLONASS,QZSS.
• High-performance 3-axis accelerometer with 16g scale.
• Enhanced memory sub-system with fast program execution.
• Huge data-flash/logger memory with a capacity of 8.5 MB.

Processor and Main-memory

• Powerful 32-bit ST ARM7 processor.
• 2112 KB fast execution RAM.
• 4532 KB Flash for firmware/application.

Storage

• 7.5 MB persistent data flash.
• 8 MB internal FAT32 flash drive.
• 1 MB circular automatic datalogger.
• 20 KB FRAM with fast access / unlimited write endurance.
• SD-CARD reader with up to 32 GB.

GSM / HSDPA

• Qualcomm QSC6270 single chip.
• 3G / HSDPA with up to 3.6 Mbps.
• UMTS / EDGE / GPRS support.
• CSD with up to 64 Kbps.
• SMS / PDU.
• DTMF decoding / transmission.
• Digitized voice playback / IVR.
• eCall Accident / Emergency services.
• Micro-SIM 1.8/3 volt.
• External and internal SIM card-reader. Switchable from the application.

GNSS / GPS

• Mediatek MT3333 Multi-GNSS chip.
• GPS, GLONASS and QZSS.
• 99 acquisition / 33 tracking channels.
• SBAS (WAAS, EGNOS, MSAS, GAGAN).
• Position update with up to 4 hz.
• A-GPS capable.
• Sensitivity. Tracking: -165 dBm Reacquisition: -160 dBm Cold start: -148 dBm.
• Accuracy: < 2.5m CEP.
• Anti-jamming, Noise cancellation.
• Active 3 volt GNSS antenna.

Electrical Specification.

• Operating voltage is 8 to 36 VDC.
• Short and reverse power protected.

Battery and Charger

• On-board 2Ah (nominal) Li-Ion battery.
• Intelligent charger with temperature throttle and sub-zero degrees support.
• On-board temperature sensor.

Digital/Analog Interface

• 4 x digital solid-state digital output. Max. 36 volt / 1.5 A per. channel. Short-circuit, ESD, Inductive kick-back protected up to 20 mH.
• 5 x digital inputs. Logic high: 8 to 40 VDC. Logic low: -5 to 3 VDC.
• Digital input #5 can be used as ignition.
• 2 x analog inputs. Range is 0..10V. Resolution: 12 bit Precision: ±1.5% FSR @ 25°C
• Protected against transients and low-pass filtered.
• Expandable I/O with MODBUS.

Communication

• Full CAN2.0B with hardware filtering and multi-speed support.
• 1 x RS232 with control signals.
• 1 x RS232 with RX/TX. Alternatively used as service port.
• 1 x RS485 with MODBUS support.
• 1-Wire bus.

Power Management

• 5 execution speeds.
• Wait for Event: Timer, Digital input, RS232, CAN, GSM, Accelerometer and power change state.
• Wait for event, from: 300 uA@12V.
• Supervision of supply voltage.
• Disable external power.

Accelerometer

• 3-axis digital acceleormeter.
• Resolution: 12 bit @ ±16g.
• Low-power mode.

External Interfaces.

• SIM-card slot for micro-SIM with lock and presence detection.
• SD-CARD slot with presence and write protect detection.
• Micro-jack 2.5” connector for hands-free.
• Audio out for digitized voice playback.
• 4 x LED indicators and 2 x DIP switches.
• Reset/recovery switch, TE-Connectivity ”Mate’n’Lock’: RS232, I/O, Power, Communicaton.
• RJ45 for RS232 with full control signals.
• SMA Female connector for GSM.
• SMB Female connector for GNSS/GPS.

Physical Characteristics

• Encapsulation: Aluminum/plastic.
• Optional mounting bracket.
• W 97 x H 35 x D 132 mm. (without antenna connectors).

Environmental Specification

• Operating temperature: -35 to 60°C.
• Battery charge temperature: -10 to 45 °C
• Recommended storage temperature: 0 to 45°C.
• Humidity: 5..90% (non condensing).

Approvals

• E1 type approval: 2004/104/EC UN ECE R10 - ed 3.
• CE mark / Applied R&TTE directive.
• GSM engine: CE/GCF/FCC/PTCRB.

Warranty

• Two-years return to factory parts and labor.
• Optional warranty up to 5 years. (restrictions apply).

Extensive Standard Features

• Standard FAT32 SD-CARD reader with up to 32 GB capacity.
• 2 x RS232 channels and 2 x RS485 channel.
• 4 x analog inputs with 0..10 volt / 0..20 mA with 12 bit precision.
• 4 x analog outputs with 0..10 volt / 0..20 mA.
• 8 x digital inputs and 8 x high-power solid-state digital outputs.
• Up to 4 digital inputs can be configured as IEC62053-31 Class A compliant.
• Expandable I/O with standard MODBUS modules.
• Full CAN 2.0B controller with hardware filtering and multi-speed support.
• 1-Wire bus for accessories such as ID-button reader, temperature sensors, etc.
• Wide operating range from 8..36 VDC.
• On-board high-capacity Li-Ion battery.
• Advanced power-management with wake-up on a wide range of events.
• High-speed Mini-USB programming connector.
• Housed in an industry standard M36 DIN compliant encapsulation.
• Two-part pluggable connectors for easy installation and maintenance.
• Fully supported by the VikMote Gateway 2 and the VikMote Deployment Server.
• Accessories: MODBUS modules, Wi-Fi, Ethernet, Bluetooth and 2 MP camera.

High Performance

• Based on the VikMote M2M Platform.
• X32 execution architecture.
• VikMote Tool with full featured device simulator.
• Huge standard API with more than 800+ functions.
• Comprehensive protocol support, including: TCP-UDP/IP, FTP, SMTP, RACP, MQTT, MODBUS.
• World-wide Quad-band GSM engine.
• Internal and external SIM-card reader.
• Digitized audio can be played over GSM or to an external device.
• DTMF support for implementation of Interactive Voice Response applications.
• Graphical 144x32 pixels display with white-on-blue back-lit text/graphics.
• Keypad with 8 keys for sophisticated user interaction and control.
• Large data-flash/logger memory with a capacity of 4.5 MB.
• Internal 4 MB FAT32 flash drive.

Cloud-based system

• Web-based system with internet access from any PC, Mobile phone or tablet.
• Modular system.
• Own VMS domain.
  • Online setup.
  • Here-and-now status display.
  • Alarm List in real time.
  • Backup Settings.
  • No subscription - no binding.
  • Data usage per. year about 12-14 Mb.
• Time stamps.
• Multi user system.
• Webservice.

Platform Advantages

• NX32 execution architecture.
• Free VikMote Tools.
• Programmable in VPL and Lua.
• Huge standard API.
• Comprehensive protocol support.
• Full featured Device Simulator.
• Sophisticated deployment tools.
• Backward and forward compatible.

Processor & main-memory

• Powerful 32-bit ST ARM7 processor.
• 1088 KB fast execution RAM.
• 2304 KB Flash for firmware/application.

Storage

• 3.5 MB persistent data flash.
• 4 MB internal FAT32 flash drive.
• 1 MB circular automatic datalogger.
• 8 KB FRAM with fast access / unlimited write endurance.
• SD-CARD reader with up to 32 GB.

GSM/UMTS

• VX40i M2 Pro+: Penta-band UMTS/HSPA. GSM: 850/900/1800/1900 MHz. UMTS: 800/850/900/1900/2100 Mhz. CSD with up to 14.4 Kbps.
• VX40i M2 Pro: Quad-band GSM. 850/900/1800/1900 MHz. GPRS Class B, Multislot 12.
• SMS / PDU.
• DTMF decoding / transmission.
• Digitized voice playback / IVR.
• Mini-SIM 1.8/3 volt.
• External SIM card-reader.
• Optional Gemalto SIM-on-chip.

User interaction

• 144x32 pixels graphical/text display. White-on-blue back-lit.
• Keypad with 8 user defined keys.
• Piezo Buzzer for user attention.
• 3 x bi-colour LED.
• Yellow status LED.
• DIP-switches.
• Reset / recovery switch.

Electrical specification

• Operating voltage is 8 to 36 VDC.
• Short and reverse power protected.

Battery and charger

• On-board 2Ah (nominal) Li-Ion battery.
• Intelligent charger with temperature throttle and sub-zero degrees support.
• On-board temperature sensor.

Digital/analog interface

• 8 x digital solid-state digital output. Max. 36 volt / 1.5 A per. channel. Short-circuit, ESD, Inductive kick-back protected up to 20 mH.
• 8 x digital inputs. Logic high: 6 to 40 VDC. Logic low: -5 to 3 VDC.
• 4 x IEC62053-31 Class A input.
• Digital input #5 can be used as ignition.
• 4 x analog inputs. Range is 0..10VDC or 0..20 mA Resolution: 12 bit Precision: ±1.5% FSR @ 25°C
• 4 x analog outputs. Range is 0..10VDC or 0..20 mA Resolution: 10 bit Precision: ±1.5% FSR @ 25°C
• Protected against transients and lowpass filtered.
• Expandable I/O with MODBUS.

Communication

• Full CAN2.0B with hardware filtering and multi-speed support.
• 1 x RS232 with control signals.
• 1 x RS485.
• 1 x shared RS232 / RS485.
• 1-Wire bus.

Power management

• 5 execution speeds.
• Wait for Event: Timer, Digital input, RS232, CAN, GSM, power change state.
• Wait for event, from: 600 uA@12V.
• Supervision of supply voltage/type.

External interfaces

• SIM-card slot for micro-SIM with lock and presence detection.
• SD-CARD slot with presence and write protect detection.
• Audio out for digitized voice playback.
• LED indicators and DIP switches.
• Reset/recovery switch.
• Two-part pluggable connector for: Power, I/O, RS485, 1Wire. CAN.
• TE-Connectivity ”Mate’n’Lock’ for: RS232/DCOUT.
• RJ45 for RS232 (EIA-561)
• SMA Female connector for GSM.
• Mini USB-B as service port.

Physical characteristics

• Encapsulation:
• 9 Module M36 DIN-rail.
• Approx. 430 gram without accessories.
• W 157 x H 86 x D 58 mm. (without SMA and screw-terminals).

Environmental specification

• Operating temperature: -30 to 60°C.
• Battery charge temperature: -10 to 45 °C
• Recommended storage temperature: 0 to 45°C.
• Humidity: 5..90% (non condensing).
• Ingress Protection: IP20.

Approvals

• EU EMC directive 2004/108/EU.
• Applied R&TTE directive.
• GSM engine: CE/GCF/FCC/PTCRB.

Warranty

• Two-years return to factory parts and labor.
• Optional warranty up to 5 years. (restrictions apply).

Extensive Standard Features

• 1 x RS232 channel / service port.
• 5 x digital inputs and 3 x high-power solid-state digital outputs.
• 2 x analog inputs with 0..10 volt / 0..20 mA.
• 2 x analog outputs with 0..10 volt / 0..20 mA.
• Up to 4 x digital inputs can be configured as IEC62053-31 Class A compliant.
• Powerful on-demand hardware options: Digital I/O option: 8 x digital inputs and 8 x digital outputs (total). Analog I/O option: 4 x analog inputs and 4 x analog outputs (total). Communication option: RS485/MODBUS and 1-Wire bus support.
• On-demand options can be applied anytime — even remotely after installation.
• Expandable I/O with standard MODBUS modules.
• 1-Wire for accessories such as ID-button reader, temperature sensors, etc.
• Wide operating range from 8..36 VDC.
• On-board Li-Ion battery.
• Advanced power-management with wake-up on a wide range of events.
• High-speed USB programming cable support.
• Housed in an industry standard M36 DIN compliant encapsulation.
• Two-part pluggable connectors for easy installation and maintenance.
• Fully supported by the VikMote Gateway 2 and the VikMote Deployment Server.

High Performance

• Based on the VikMote M2M Platform.
• X32 execution architecture.
• VikMote Tool with full featured device simulator.
• Huge standard API with more than 800+ functions.
• Comprehensive protocol support, including: TCP-UDP/IP, FTP, SMTP, RACP, MQTT, MODBUS.
• World-wide Quad-band GSM engine.
• Internal SIM-card reader.
• Large data-flash/logger memory with a capacity of 4.5 MB.
• Internal 4 MB FAT32 flash drive.

Cloud-based system

• Web-based system with internet access from any PC, Mobile phone or tablet.
• Modular system.
• Own VMS domain.
• Online setup.
• Here-and-now status display.
• Alarm List in real time.
• Backup Settings.
• No subscription - no binding.
• Data usage per. year about 12-14 Mb.
• Time stamps.
• Multi user system.
• Webservice.

Platform Advantages

• NX32 execution architecture.
• Free VikMote Tools.
• Programmable in VPL and Lua.
• Huge standard API.
• Comprehensive protocol support.
• Full featured Device Simulator.
• Sophisticated deployment tools.
• Backward and forward compatible.

Processor & main-memory

• Powerful 32-bit ST ARM7 processor.
• 1088 KB fast execution RAM.
• 2304 KB Flash for firmware/application.

Storage

• 3.5 MB persistent data flash.
• 4 MB internal FAT32 flash drive.
• 1 MB circular automatic datalogger.
• 8 KB FRAM with fast access /unlimited write endurance.

GSM

• Quad-band GSM engine. 850/900/1800/1900 MHz.
• GPRS Class B, Multislot 10.
• CSD with up to 19 Kbps.
• SMS / PDU.
• Micro-SIM 1.8/3 volt.
• Internal SIM card-reader.
• Optional Gemalto SIM-on-chip.

User interaction

• 3 x bi-colour LED.
• Yellow status LED.
• Reset / recovery switch.

Electrical specification

• Operating voltage is 8 to 36 VDC.
• Short and reverse power protected.

Battery and charger

• On-board 1Ah (nominal) Li-Ion battery.
• Intelligent charger with temperature throttle and sub-zero degrees support.
• On-board temperature sensor.

Digital/analog interface

• Up to 8 x solid-state digital outputs. Max. 36 volt / 1.5 A per. channel. Short-circuit, ESD, Inductive kick-back protected up to 20 mH.
• Up to 8 x digital inputs. Logic high: 6 to 40 VDC. Logic low: -5 to 3 VDC.
• Digital input #5 can be used as ignition.
• 4 x IEC62053-31 Class A input.
• Up to 4 x analog inputs. Range is 0..10VDC or 0..20 mA Resolution: 10 bit Precision: ±1.5% FSR @ 25°C
• Up to 4 x analog outputs. Range is 0..10VDC or 0..20 mA Resolution: 10 bit Precision: ±1.5% FSR @ 25°C
• Protected against transients and lowpass filtered.
• Expandable I/O with MODBUS.

Communication

• 1 x RS232/service port.
• 1 x RS485 (on-demand)
• 1-Wire bus (on-demand)

Power management

• 5 execution speeds.
• Wait for Event: Timer, Digital input, RS232, GSM, power change state.
• Wait for event, from: 600 uA@12V.
• Supervision of supply voltage / type.

On-demand HW options

• Applied ”any-time” - locally or remotely.
• Over-the-air hardware upgrade.

Physical characteristics

• Encapsulation: 9 Module M36 DIN-rail.
• Approx. 330 gram without accessories.
• W 157 x H 86 x D 58 mm. (without SMA and screw-terminals).

Environmental specification

• Operating temperature: -30 to 60°C.
• Battery charge temperature: -10 to 45 °C
• Recommended storage temperature: 0 to 45°C.
• Humidity: 5..90% (non condensing).
• Ingress Protection: IP20.

Approvals

• CE. EU EMC directive 2004/108/EU.
• Applied R&TTE directive.
• GSM engine: CE/GCF/FCC/PTCRB.

Warranty

• Two-years return to factory parts and labor.
• Optional warranty up to 5 years. (restrictions apply).

 Extensive Standard Features

• RS232 channel with optional shared RS485 channel.
• 2 x analog inputs with 0..10 volt / 0..20 mA with 12 bit precision.
• 5 x digital inputs and 4 x high-power relays.
• Up to 4 digital inputs can be configured as IEC62053-31 Class A compliant.
• Expandable I/O with standard MODBUS modules.
• 1-Wire bus for accessories such as ID-button reader, temperature sensors, etc.
• Wide AC/DC power operating range from 100..260VAC / 8..36 VDC.
• On-board Li-Ion battery.
• 24 Volt DC-out capability for powering external equipment.
• Advanced power-management with wake-up on a wide range of events.
• High-speed mini-USB programming connector.
• Housed in an ruggedized plastic encapsulation with cable glands.
• IP65 water protected for outdoor usage.
• Fully supported by the VikMote Gateway 2 and the VikMote Deployment Server..
• Accessories: 1-wire accessories, MODBUS modules, etc.

Device Advantages

• Quad-band GSM engine.
• Internal/external antenna.
• Digital and analog input/output.
• AC/DC relay outputs.
• RS232/RS485 channels.
• MODBUS expandable I/O.
• 1-Wire bus.
• Digitized voice playback.
• DTMF decoding/transmission.
• Micro SD-CARD with up to 32 GB.
• FAT32 file-system.
• AC / DC powered.
• Backup battery.
• IP65 Ingress Protection
• State of the art power-management.

High Performance

• Based on the VikMote M2M Platform.
• NX32 execution architecture.
• VikMote tools with full featured device simulator.
• Huge standard API with more than 800+ functions.
• Comprehensive protocol support, including: TCP-UDP/IP, FTP, SMTP, RACP, MQTT, MODBUS.
• Full backward-compatibility with existing X32 applications.
• World-wide Quad-band GSM engine.
• Internal and external GSM antenna connector. Selectable from application.
• Internal SIM-card reader.
• Digitized audio can be played over GSM.
• DTMF support for implementation of Interactive Voice Response applications.
• Enhanced memory sub-system with fast program execution.
• Huge data-flash/logger memory with a capacity of 4.5 MB.
• Internal 4 MB FAT32 flash drive.
• Standard FAT32 SD-CARD reader with up to 32 GB capacity.

Cloud-based system

• Web-based system with internet access from any PC, Mobile phone or tablet.
• Modular system.
• Own VMS domain.
  • Online setup.
  • Here-and-now status display.
  • Alarm List in real time.
  • Backup Settings.
  • No subscription - no binding.
  • Data usage per. year about 12-14 Mb.
• Time stamps.
• Multi user system.
• Webservice.

Platform Advantages

• NX32 execution architecture.
• Free VikMote Tools.
• Programmable in VPL and Lua.
• Huge standard API.
• Comprehensive protocol support.
• Full featured Device Simulator.
• Sophisticated deployment tools.
• Backward and forward compatible.

Processor and Main-memory

• Powerful 32-bit ST ARM7 processor.
• 2112 KB fast execution RAM.
• 4532 KB flash for firmware/application.

Storage

• 4.5 MB persistent data flash.
• 4 MB internal FAT32 flash drive.
• 1 MB circular automatic datalogger.
• 20 KB FRAM with fast access/unlimited write endurance.
• SD-CARD reader with up to 32 GB.

GSM

• 850/900/1800/1900 Mhz.
• GPRS Multi-slot class 12.
• Max. 85.6 kbps (up/down link)
• CSD with up to 14.4 Kbps.
• SMS / PDU.
• DTMF decoding / transmission.
• Digitized voice playback / IVR.
• Mini-SIM 1.8/3 volt.
• Internal SIM card-reader.
• Internal GSM antenna.
• External or internal antenna selectable by DIP-switch or user application
• Optional Gemalto eSIM.

User Interaction

• Three bi-colour LED/Yellow status.
• DIP-switches.
• Reset/recovery switch.
• Antenna selection dip-switch.
• Configuration jumpers.
• Mini-USB for service port.

Battery and Charger

• On-board 1Ah (nominal) Li-Ion battery.
• Intelligent charger with temperature throttle and sub-zero degrees support.
• On-board temperature sensor.

Digital/Analog Interface

• 4 x relay output. Max. 5A @ 250VAC/30 VDC
• 5 x digital inputs. Logic high: 6 to 40 VDC. Logic low: -5 to 3 VDC.
• 4 x IEC62053-31 Class A input.
• Digital input #5 can be used as ignition.
• 2 x analog inputs. Range is 0..10VDC or 0..20 mA Resolution: 12 bit Precision: ±1.5% FSR @ 25°C
• Protected against transients and lowpass filtered.
• Expandable I/O with MODBUS.

Communication

• RS232 channel.
• On-demand: RS485 (shared).
• 1-Wire bus.

Power Management

• 5 execution speeds.
• Wait for Event: Timer, Digital input, RS232, GSM, Power change state.
• Wait for event, from: 600 uA@12V.
• Supervision of supply voltage/type.

Electrical Specification

• Supply operating range: 8 to 36 VDC. 100 to 260 VAC.
• Short and reverse power protected.

Internal Interfaces

• Screw-terminals for: Power, I/O and 24V DCOUT.
• Angled screw-terminals for: RS232, RS485, 1-Wire.
• Mini-USB for programming/service.

On-Demand Hardware Options

• Applied ”any-time”- locally or remotely.
• Over-the-air hardware upgrade.

External Interfaces

• SMA Female connector for external GSM antenna.
• 3 x PG11 cable glands.
• 2 x PG9 blind plugs.

Physical Characteristics

• Encapsulation: Durable Polycarbonate plastic.
• Approx. 690 gram without accessories.
• W 130 x H 180 x D 60 mm. (without SMA and PG connectors)

Environmental Specification

• Operating temperature: -30 to 60°C.
• Battery charge temperature: -10 to 45 °C
• Recommended storage temperature: 0 to 45°C.
• Humidity: 5..90% (non condensing).
• Ingress Protection: IP65.

Approvals

• R&TTE 1995/5/EC.
• CE. EMC directive 2004/108/EU.
• GSM engine: CE/GCF/FCC/PTCRB.

Warranty

• Two-years return to factory parts and labor.
• Optional warranty up to 5 years. (restrictions apply).

Extensive Standard Features

• Internal 8 MB FAT32 flash drive.
• Standard FAT32 Micro SD-CARD reader with up to 32 GB capacity.
• 2 x RS232 channels and 2 x RS485 channel.
• 4 x analog inputs with 0..10 volt / 0..20 mA with 12 bit precision.
• 4 x analog outputs with 0..10 volt / 0..20 mA.
• 5 x digital inputs and 4 x high-power relays.
• Up to 4 digital inputs can be configured as IEC62053-31 Class A compliant.
• Expandable I/O with standard MODBUS modules.
• 1-Wire bus for accessories such as ID-button reader, temperature sensors, etc.
• Wide AC/DC power operating range from 100..260VAC / 8..36 VDC.
• On-board high-capacity Li-Ion battery.
• Advanced power-management with wake-up on a wide range of events.
• High-speed USB programming connector.
• Tntrusion detection.
• Housed in an ruggedized plastic encapsulation with cable glands.
• IP65 water protected for outdoor usage.
• Fully supported by the VikMote Gateway 2 and the VikMote Deployment Server.

High Performance

• Based on the VikMote M2M Platform.
• NX32 execution architecture.
• VikMote Tools with full featured device simulator.
• Huge standard API with more than 800+ functions.
• Comprehensive protocol support, including: TCP-UDP/IP, FTP, SMTP, RACP, MQTT, MODBUS, NMP/Garmin FMI.
• Full backward-compatibility with existing X32 applications.
• High-speed 3G/HSDPA GSM engine. Backward compatible with 2G/2.5G.
• On-board Ethernet interface.
• Medium range ISM band RF transceiver with on-board antenna.
• Internal and external GSM antenna connector. Selectable from application.
• Internal SIM-card reader.
• Digitized audio can be played over GSM.
• DTMF support for implementation of Interactive Voice Response applications.
• Enhanced memory sub-system with fast program execution.
• Huge data-flash/logger memory with a capacity of 8.5 MB.

Device Advantages

• 3G/HSDPA GSM engine.
• Internal/external antenna.
• On-boad Ethernet interface.
• Digital and analog input/output.
• AC/DC relay outputs.
• Multiple RS232/RS485 channels.
• MODBUS expandable I/O.
• 1-Wire bus.
• ISM medium range RF.
• Digitized voice playback.
• DTMF decoding/transmission.
• Large flash memory capacity.
• Micro SD-CARD with up to 32 GB.
• FAT32 file-system.
• AC / DC powered.
• High-capacity battery.
• IP65 Ingress Protection

Cloud-based system

• Web-based system with internet access from any PC, Mobile phone or tablet.
• Modular system.
• Own VMS domain.
  • Online setup.
  • Here-and-now status display.
  • Alarm List in real time.
  • Backup Settings.
  • No subscription - no binding.
  • Data usage per. year about 12-14 Mb.
• Time stamps.
• Multi user system.
• Webservice.

Platform Advantages

• NX32 execution architecture.
• Free VikMote Tools.
• Programmable in VPL and Lua.
• Huge standard API.
• Comprehensive protocol support.
• Full featured Device Simulator.
• Sophisticated deployment tools.
• Backward and forward compatible.
• Deployment Features • Full Vikingegaarden GPRS Gateway Professional / Upgrade & Deployment server compatible.
• Upgrade of application, firmware and parameters over CSD, GPRS and Cable.
• Upgrade can occur during full unit operation minimizing the impact on the customer.
• Unattended and fully automatic upgrade and deployment.
• Automatic ”bootstrap” of un-programmed unit on first time installation.

Processor and Main-memory

• Powerful 32-bit ST ARM7 processor.
• 2112 KB fast execution RAM.
• 4532 KB Flash for firmware/application.

Storage

• 7.5 MB persistent data flash.
• 8 MB internal FAT32 flash drive.
• 1 MB circular automatic datalogger.
• 20 KB FRAM with fast access /unlimited write endurance.
• SD-CARD reader with up to 32 GB.

GSM

• Qualcom QSC6270 single chip.
• 3G / HSDPA with up to 3.6 Mbps.
• UMTS / EDGE / GPRS support.
• CSD with up to 64 Kbps.
• SMS / PDU.
• DTMF decoding / transmission.
• Digitized voice playback / IVR.
• eCall Accident / Emergency services.
• Micro-SIM 1.8/3 volt.
• Internal SIM card-reader.
• Internal GSM antenna.
• External or internal antenna selectable by DIP-switch or user application.
• Optional Gemalto SIM-on-chip.

User Interaction

• Three bi-colour LED / Yellow status.
• DIP-switches.
• Reset/recovery switch.
• Antenna selection dip-switch.
• Configuration jumpers.
• Mini-USB for service port.
• Intrusion-detection.

Electrical Specification

• Supply operating range: 8 to 36 VDC. 100 to 260 VAC.
• Short and reverse power protected.

Battery and Charger

• On-board 2Ah (nominal) Li-Ion battery.
• Intelligent charger with temperature throttle and sub-zero degrees support.
• On-board temperature sensor.

Digital/Analog Interface

• 4 x relay output.  Max. 5A @ 250VAC / 30 VDC
• 5 x digital inputs. Logic high: 6 to 40 VDC. Logic low: -5 to 3 VDC.
• 4 x IEC62053-31 Class A input.
• Digital input #5 can be used as ignition.
• 4 x analog inputs. Range is 0..10VDC or 0..20 mA  Resolution: 12 bit  Precision: ±1.5% FSR @ 25°C
• 4 x analog outputs.  Range is 0..10VDC or 0..20 mA  Resolution: 10 bit  Precision: ±1.5% FSR @ 25°C
• Protected against transients and lowpass  filtered.
•  Expandable I/O with MODBUS.

Communication

• 10BASE-T Ethernet inferface.
•  1 x RS232 with control signals.
•  1 x RS485.
•  1 x shared RS232 / RS485.
•  1-Wire bus.
•  On-board 868 Mhz ISM RF Up to 15 meter indoor / Up to 50 meter outdoor.
•  ISM RF can be disabled for world-wíde compliance requirements.

External Interfaces.

•  SMA Female connector for external GSM antenna.
•  3 x PG11 cable glands.
• 2 x PG9 blind plugs.

Power Management

• 5 execution speeds.
• Wait for Event: Timer, Digital input, RS232, GSM, Power change state, RF and Intrusion.
• Wait for event, from: 600 uA@12V.
• Supervision of supply voltage / type.

Internal Interfaces.

• Screw-terminals for:  Power, I/O and 12/24V DCOUT.
• Angled screw-terminals for:  RS232, RS485, 1-Wire and 3.3V DCOUT.
• Mini-USB for programming/service.
• Standard RJ45 Ethernet connector.

Physical Characteristics

• Encapsulation:  Durable Polycarbonate plastic.
• Approx. 690 gram without accessories.
• W 130 x H 180 x D 60 mm. (without SMA and PG connectors).

Environmental Specification

• Operating temperature: -30 to 60°C.
•  Battery charge temperature:  -10 to 45°C
•  Recommended storage temperature:  0 to 45°C.
•  Humidity: 5..90% (non condensing).
• Ingress Protection: IP65.

Approvals

• R&TTE 1995/5/EC.
• CE. EMC directive 2004/108/EU.
• GSM engine: CE/GCF/FCC/PTCRB.

Warranty

• Two-years return to factory parts and labor.
• Optional warranty up to 5 years. (restrictions apply).

Extensive Standard Features

• 2 Digital inputs, 2 Digital output and 2 Analog inputs.
• Dedicated high-speed USB programming port providing improved communication speed.
• Standard RS232 serial port. Alternatively used as service port.
• 1-wire bus for connection to temperature sensors, ID-button readers, etc.
• Full support for the Navigation and Messaging Platform available from Logic IO.
• One user available bi-color LED-Indicators with 3 colors: Green, Red and Yellow.
• One bi-color and one yellow system LED indicating state of GSM, Power management and Battery charging etc.
• High performance +/-16g 3-axis accelerometer / movement sensor.
• On-board dipswitch for input configuration and general use. Temperature sensor.

Communication Technology

• SX10 PRO: Quad Band (850/900/1800/1900 Mhz) GSM.
• SX10 PRO-r: Triple Band (900/1800/1900 Mhz) GSM-R for GSM-Rail system.
  • SMS (Text and PDU)
  • GPRS. Multislot class 10
  • CSD (Datacall)
  • On-board internal chip antenna. Prepared for external antenna connection.
• On-board high-sensitivity GPS-receiver with extremely fast acquisition and low-power consumption.
  • Full SBAS (EGNOS / WAAS / MSAS) support for enhanced GPS precision
  • Prepared for A-GPS.
  • On-board internal patch antenna. Prepared for external antenna connection.
• On-Board medium range RF transceiver (868 MHz)
  • On-board internal chip antenna prepared for external antenna connection.

High Performance

• Powerful industry leading dedicated 32-bit ARM7 Processor.
• Very fast execution (48 MHz).
• 1088 KByte RAM.
• 2304 KByte Flash for application and database.
• 512 Kbyte Dataflash for datalogging / parameters.
• Support for additional 8 MByte DataFlash.
• 512 Kbyte internal flash drive with FAT compatible file-system, for easy sharing of files with a PC.
• 8 KByte FRAM for fast access memory without any write endurance limitations.
• Micro-SD Card Reader with FAT32 file-system and up to 32 GB capacity.

Flexible Power

• Powered from internal battery pack and/or from external powers source.
• Several battery configurations supported:
  • 58 Ah (nominel) non-rechargeable battery. Height: 56 mm.
  • 24 Ah (nominel) non-rechargeable battery. Height: 43 mm.
  • 10 Ah (nominel) rechargeable battery. Height: 43 mm.
  • 2 Ah (nominel) rechargeable battery. Height: 43 mm.
• Automatic switch-over from external to internal power.
• Automatic charging and maintenance of rechargeable battteries.
• Integrated dynamic battery power consumption measurement circuit for management and statistical purposes.
• During service and development the unit is powered directly from USB.
• Development Tools
• Programmable using the VikMote Tool full-feature development environment.
• Easy to learn VPL high-level programming language based on the EIC 1131-3 industrial standard.
• More than 800+ standard functions and 1000 pages of on-line documentation suits every application.
• Many example programs available to ”kick-start” application development.
• Full feature Microsoft Windows Simulator allowing test of complete application without use of physical unit.
• VSMS technology seamlessly supports SMS, GPRS, CSD without application/server changes.
• Seamless upgrade to future technologies.

Cloud-based system

• Web-based system with internet access from any PC, Mobile phone or tablet.
• Modular system.
• Own VMS domain.
  • Online setup.
  • Here-and-now status display.
  • Alarm List in real time.
  • Backup Settings.
  • No subscription - no binding.
  • Data usage per. year about 12-14 Mb.
• Time stamps.
• Multi user system.
• Webservice.

Advanced Power Management

• Several power-saving modes: Zero Power, ’Wait for Event’, zero-power and 5 processor execution steps.
• Wakeup from ’Wait for Event’ using: Digital input, 3D movement sensor, Timeout, GSM- or UART activity.
• Advanced power saving mode while awaiting 2D/3D GPS fix.
• Zero Power saving mode reducing the power consumption to virtually none with wake-up from:
  • 3D movement sensor.
  • Digital inputs.
  • Timer.
• Integrated dynamic battery power consumption measurement circuit for management and statistical purposes.

Deployment Features

• Full Vikingegaarden GPRS Gateway Professional / Upgrade & Deployment server compatible.
• Upgrade of application, firmware and parameters over CSD, GPRS and Cable.
• Upgrade can occur during full unit operation minimizing the impact on the customer.
• Unattended and fully automatic upgrade and deployment.
• Automatic ”bootstrap” of un-programmed unit on first time installation.