+45 7580 3960

IoT enheder til dataopsamling og fjernstyring af forskellige operationer samt for GPS tracking af køretøjer – fra simple on/off funktion til tovejs datakommunikation mellem SCADA systemer og procesudstyr.

Enhedsserien hedder VikMote, og har indbygget datalogger, GPS-tracker, GSM-modem og batteri-backup. Enhederne er inddelt i 5 grundlæggende modeller. Stand-alone enheder og tavler klar til montering fås med kraftfulde IoT-applikationer inden for:

  • Måling og automatisk registrering af el-, vand- og varmeforbrug
  • Overvågning af forskellige operationer
  • Dataopsamling fra forskellige ind- og udgange
  • GPS-sporing af sweeper-køretøjer til dokumentation af opgaver udført for staten eller kommunen
  • Ladestationer til elbiler

VikMote VX10 serienVikMote VX10

  • Kan tilsluttes op til to målepunkter
  • Prisbillig løsning
  • Kompakt og let at montere
  • Ideel til indbygning, hvor der er begrænset plads
  • Kan anvendes til stationær såvel som mobil datalogning samt GPS-tracking
  • Kan anvendes til overvågning og fjernbetjening af processer over GSM-net og datafangst

VikMote VX10 highlights (only in English)

Extensive Standard Features

  • Internal 4 MB FAT32 flash drive.
  • 1 x digital inputs and
    1 x high-power solid-state digital output (upgradeable).
  • Wide operating range from 8..36 VDC.
  • On-board Li-Ion battery.
  • Advanced power-management with wake-up on a wide range of events.
  • High-speed Mini-USB programming connector.
  • Support the Garmin Fleet Management Interface.
  • Fully supported by the VikMote Gateway 2 and the VikMote Deployment Server.
  • Ruggedized IP66 plastic encapsulation.
  • Delivered with GSM/GPS antennas pre-mounted and with 50 cm interface cable.
  • Powerful on-demand hardware options:
    • I/O:
      2 x digital inputs,
      2 x digital outputs and
      1 x analog input (total).
    • RF: Medium range ISM band RF transceiver with on-board antenna.
    • FLASH: Micro-SD card reader and 3 MB extended flash.
    • COM: RS232/FMI and
    • 1-Wire bus (warp) or CAN (warp-c).
  • On-demand options can be applied anytime — even remotely after installation.

Platform Advantages

  • NX32 execution architecture.
  • Free VikMote Tools.
  • Programmable in VPL.
  • Huge standard API.
  • Comprehensive protocol support.
  • Full featured Device Simulator.
  • Sophisticated deployment tools.
  • Backward and forward compatible.

Deployment Features

  • Full Vikingegaarden GPRS Gateway Professional / Upgrade & Deployment server compatible.
  • Upgrade of application, firmware and parameters over CSD, GPRS and Cable.
  • Upgrade can occur during full unit operation minimizing the impact on the customer.
  • Unattended and fully automatic upgrade and deployment.
  • Automatic ”bootstrap” of un-programmed unit on first time installation.

Cloud-based system

  • Web-based system with internet access from any PC, Mobile phone or tablet.
  • Modular system.
  • Own VMS domain.
    • Online setup.
    • Here-and-now status display.
    • Alarm List in real time.
    • Backup Settings.
    • No subscription - no binding.
    • Data usage per. year about 12-14 Mb.
  • Time stamps.
  • Multi user system.
  • Webservice.

Performance

  • High Performance
  • Based on the VikMote M2M Platform.
  • X32 execution architecture.
  • VikMote Tools with full featured device simulator.
  • Huge standard API with more than 800+ functions.
  • Comprehensive protocol support, including: TCP-UDP/IP, FTP, SMTP, RACP, MQTT, MODBUS, FMS/J1939, Garmin FMI.
  • World-wide Quad-band GSM engine.
  • Internal SIM-card reader.
  • State-of-the art SuperGPS positioning engine.
  • High-performance 3-axis accelerometer with 16g scale.
  • Large data-flash/logger memory with a capacity up to 4.5 MB.

VikMote VX10 specifikationer (only in English)

Processor & Main-memory

  • Powerful 32-bit ST ARM7 processor.
  • 1088 KB fast execution RAM.
  • 2304 KB Flash for firmware/application.

Storage

  • 3.5 MB persistent data flash.
  • 4 MB internal FAT32 flash drive.
  • 1 MB circular automatic datalogger.
  • 8 KB Virtual FRAM with fast access / unlimited write endurance.
  • Micro SD-CARD reader. Up to 32 GB.

GSM

  • Quad-band GSM engine. 850/900/1800/1900 MHz.
  • GPRS Class B, Multislot 10.
  • CSD with up to 19 Kbps.
  • SMS / PDU.
  • Micro-SIM 1.8/3 volt.
  • Optional Gemalto SIM-on-chip.
  • Delivered with ’thumb’ antenna.

SuperGPS

  • Mediatek MT3329 Single Chip.
  • 66 acquisition / 22 tracking channels.
  • SBAS (WAAS,EGNOS,MSAS).
  • Prepared for A-GPS.
  • Position update with up to 4 hz.
  • Sensitivity. Tracking: -165 dBm Reacquisition: -160 dBm Cold start: -148 dBm.
  • Accuracy: < 2.5m CEP.
  • Active 3 volt GNSS antenna.
  • Delivered with a tiny magnet antenna with 2 meter cable.

Battery and Charger

  • On-board 900mA (nom.) Li-Ion battery.
  • Intelligent charger with temperature throttle and sub-zero degrees support.
  • On-board temperature sensor.

Electrical Specification

  • Operating voltage is 8 to 36 VDC.
  • Short and reverse power protected.

Digital/Analog Interface

  • 2 x digital solid-state digital output. Max. 36 volt / 0.75 A per. channel. Short-circuit, ESD, Inductive kick-back protected up to 20 mH.
  • 2 x digital inputs. Logic high: 8 to 40 VDC. Logic low: -5 to 3 VDC.
  • Digital input #1 can be used as ignition.
  • 1 x analog input. Range is 0..10V. Resolution: 10 bit Precision: ±1.5% FSR @ 25°C

Communication

  • Warp-c: Full CAN2.0B with hardware filtering and multi-speed support.
  • Warp: RS232 and 1-Wire bus.
  • On-board 868 Mhz ISM RF Up to 15 meter indoor / Up to 50 meter outdoor.

Power Management

  • 5 execution speeds.
  • Wait for Event: Timer, Digital input, RS232, CAN, GSM, Accelerometer and power change state.
  • Wait for event, from: 600 uA@12V.
  • Supervision of supply voltage / type.

Accelerometer

  • 3-axis digital acceleormeter.
  • Resolution: 12 bit @ ±16g.
  • Low-power mode.

Internal Interface

  • Mini-USB connector for service port.
  • SIM-card slot for micro-SIM.
  • Micro SD-CARD slot.
  • Reset/recovery switch.

External Interface

  • 2 x bi-color LED indicators.
  • Yellow LED for status.
  • SMA female connector for GSM antenna.
  • SMA female connector for GPS antenna.

On-Demand Hardware Options

  • Applied ”any-time” - locally or remotely.
  • Over-the-air hardware upgrade.

Physical Characteristics

  • Encapsulation: Black UL94 plastic.
  • Sealing membrane.
  • 50 cm open-ended interface cable.
  • Approx. 250 gram without accessories.
  • W 92 x H 30 x D 58 mm. (without mounting flanges).

Environmental Specification

  • Operating temperature: -30 to 55°C.
  • Battery charge temperature: -10 to 45 °C
  • Recommended storage temperature: 0 to 45 °C.
  • Humidity: 5..90% (non condensing).
  • IP-66 ingress protected.

Approvals

  • E1 type approval: 2004/104/EC UN ECE R10.
  • CE mark / Applied R&TTE directive.
  • GSM Engine: CE/GCF/FCC/PTCRB.

Warranty

  • Two-years return to factory parts and labor.
  • Optional warranty up to 5 years. (restrictions apply).

Hent teknisk manual til VikMote VX10 serien

Om VikMote VX20 Encore

  • Kompakt og let at montere
  • Ideel til indbygning, hvor der er begrænset plads
  • Anvendes til GPS-tracking
  • Anvendes til overvågning og fjernbetjening af processer over GSM-net og datafangst
Indgår i følgende løsninger:Vision, Gate2Gate, RoadPrint, FlexGuard

VikMote VX20 Encore highlights (only in English)

Extensive Standard Features

  • Internal 4 MB FAT32 flash drive.
  • 1 x RS232 channel.
  • 2 x analog inputs with 0..10 volt / 12 bit precision.
  • 5 x digital inputs and 4 high-power solid-state digital outputs.
  • 1-Wire bus for accessories such as ID-button reader, temperature sensors, etc.
  • Powerful on-demand hardware options:
    • Full CAN 2.0B controller with hardware filtering and multi-speed support.
    • RS485 channel with MODBUS and expandable I/O.
    • Internal SIM-card reader. Active reader selectable from the application.
  • On-demand options can be applied anytime - even remotely after installation.
  • Wide operating range from 8..36 VDC.
  • External power can be selectable enabled/disabled by the application.
  • On-board high-capacity Li-Ion battery.
  • Advanced power-management with wake-up on a wide range of events.
  • High-speed USB programming cable support.
  • Fully supported by the VikMote Gateway 2 and the VikMote Deployment Server.
  • Exclusive and durable aluminum encapsulation.

Platform Advantages

  • NX32 execution architecture.
  • Free VikMote Tools.
  • Programmable in VPL and Lua.
  • Huge standard API.
  • Comprehensive protocol support.
  • Full featured Device Simulator.
  • Sophisticated deployment tools.
  • Backward and forward compatible.

Device Advantages

  • Quad band GSM engine.
  • Multi-GNSS positioning engine.
  • Internal FAT32 flash-drive.
  • Internal and external SIM reader.
  • 3-axis accelerometer.
  • Full CAN 2.0B support.
  • 1-Wire bus.
  • RS232 and RS485 channels.
  • Digital and analog I/O.
  • Digitized voice playback.
  • DTMF decoding/transmission.
  • High-capacity battery.
  • State of the art power-management.
  • On-demand hardware options.

Deployment Features

  • Full Vikingegaarden / Upgrade & Deployment server compatible.
  • Upgrade of application, firmware and parameters over CSD, GPRS and Cable.
  • Upgrade can occur during full unit operation minimizing the impact on the customer.
  • Unattended and fully automatic upgrade and deployment.
  • Automatic ”bootstrap” of un-programmed unit on first time installation.

Cloud-based system

  • Web-based system with internet access from any PC, Mobile phone or tablet.
  • Modular system.
  • Own VMS domain.
    • Online setup.
    • Here-and-now status display.
    • Alarm List in real time.
    • Backup Settings.
    • No subscription - no binding.
    • Data usage per. year about 12-14 Mb.
  • Time stamps.
  • Multi user system.
  • Webservice.

High Performance

  • Based on the VikMote M2M Platform.
  • Cost-efficient variant of the VX20 TURBO.
  • NX32 execution architecture.
    • VikMote tools with full featured device simulator.
    • Huge standard API with more than 800+ functions.
    • Comprehensive protocol support, including: TCP-UDP/IP, FTP, SMTP, RACP, MQTT, MODBUS, FMS/J1939, NMP/Garmin FMI.
    • Fully backward compatibility with existing X32 applications.
  • World-wide Quad-band GSM engine.
  • External SIM-card reader.
  • Digitized audio can be played over GSM or to an external device.
  • DTMF support for implementation of Interactive Voice Response applications.
  • State-of-the art Multi-GNSS positioning engine with GPS,GLONASS,QZSS.
  • High-performance 3-axis accelerometer with 16g scale.
  • Enhanced memory sub-system with fast program execution.
  • Huge data-flash/logger memory with a capacity of 4.5 MB.

VikMote VX20 Encore specifications (only in English)

Processor and Main-memory

  • Powerful 32-bit ST ARM7 processor.
  • 2112 KB fast execution RAM.
  • 4532 KB Flash for firmware/application.

Storage

  • 3.5 MB persistent data flash.
  • 4 MB internal FAT32 flash drive.
  • 1 MB circular automatic datalogger.
  • 20 KB FRAM with fast access / unlimited write endurance.

GSM

  • 850/900/1800/1900 Mhz.
  • GPRS Multi-slot class 12.
  • Max. 85.6 kbps (up/down link)
  • CSD with up to 14.4 Kbps.
  • SMS / PDU.
  • DTMF decoding / transmission.
  • Digitized voice playback / IVR.
  • Micro-SIM 1.8/3 volt.
  • External and internal SIM card-reader.
  • Switchable from the application.

GNSS / GPS

  • Mediatek MT3333 Multi-GNSS chip.
  • GPS, GLONASS and QZSS.
  • 99 acquisition / 33 tracking channels.
  • SBAS (WAAS ,EGNOS, MSAS, GAGAN).
  • Position update with up to 4 hz.
  • A-GPS capable.
  • Sensitivity. Tracking: -165 dBm Reacquisition: -160 dBm Cold start: -148 dBm.
  • Accuracy: < 2.5m CEP.
  • Anti-jamming, Noise cancellation.
  • Active 3 volt GNSS antenna.

Electrical Specification.

  • Operating voltage is 8 to 36 VDC.
  • Short and reverse power protected.

Battery and Charger

  • On-board 2Ah (nominal) Li-Ion battery.
  • Intelligent charger with temperature throttle and sub-zero degrees support.
  • On-board temperature sensor.

Digital/Analog Interface

  • 4 x digital solid-state digital output. Max. 36 volt / 1.5 A per. channel.
  • Short-circuit, ESD, Inductive kick-back protected up to 20 mH.
  • 5 x digital inputs. Logic high: 8 to 40 VDC. Logic low: -5 to 3 VDC.
  • Digital input #5 can be used as ignition.
  • 2 x analog inputs. Range is 0..10V. Resolution: 12 bit Precision: ±1.5% FSR @ 25°C
  • Protected against transients and low-pass filtered.
  • Expandable I/O with MODBUS.

Communication

  • Full CAN2.0B with hardware filtering and multi-speed support.
  • 1 x RS232 with RX/TX. Alternatively used as service port.
  • 1 x RS485 with MODBUS support.
  • 1-Wire bus.

Power Management

  • 5 execution speeds.
  • Wait for Event: Timer, Digital input, RS232, CAN, GSM, Accelerometer and power change state.
  • Wait for event, from: 300 uA@12V.
  • Supervision of supply voltage.
  • Disable external power.

Accelerometer

  • 3-axis digital acceleormeter.
  • Resolution: 12 bit @ ±16g.
  • Low-power mode.

On-Demand Hardware Options

  • Applied ”any-time” - locally or remotely.
  • Over-the-air hardware upgrade.

External Interfaces

  • SIM-card slot for micro-SIM with lock and presence detection.
  • 4 x LED indicators.
  • Reset/recovery switch
  • TE-Connectivity ”Mate’n’Lock’: RS232, I/O, Power, Communicaton.
  • SMA Female connector for GSM.

Physical Characteristics

  • Encapsulation: Aluminum/plastic.
  • Optional mounting bracket.
  • Approx. 290 gram without accessories.
  • W 97 x H 35 x D 132 mm. (without antenna connectors).

Environmental Specification

  • Operating temperature: -35 to 60°C.
  • Battery charge temperature: -10 to 45 °C
  • Recommended storage temperature: 0 to 45°C.
  • Humidity: 5..90% (non condensing).
  • IP30 with SIM/Connectors in use.

Approvals

  • E1 type approval: 2004/104/EC UN ECE R10 - ed 3.
  • CE mark / Applied R&TTE directive.
  • GSM engine: CE/GCF/FCC/PTCRB.

Warranty

  • Two-years return to factory parts and labor.
  • Optional warranty up to 5 years. (restrictions apply).
Note: Some features are currently under development.

Om VikMote VX20 Turbo+VikMote VX20 Turbo+

  • Kompakt og let at montere
  • Ideel til indbygning, hvor der er begrænset plads
  • Anvendes til GPS-tracking
  • Anvendes til overvågning og fjernbetjening af processer over GSM-net og datafangst
Indgår i følgende løsninger: Vision, Gate2Gate, RoadPrint, FlexGuard

VikMote VX20 Turbo+ highlights (only in English)

Extensive Standard Features

  • Internal 8 MB FAT32 flash drive.
  • Standard FAT32 SD-CARD reader with up to 32 GB capacity.
  • 2 x RS232 channels and 1 x RS485 channel.
  • 2 x analog inputs with 0..10 volt / 12 bit precision.
  • 5 x digital inputs and 4 high-power solid-state digital outputs.
  • Full CAN 2.0B controller with hardware filtering and multi-speed support.
  • 1-Wire bus for accessories such as ID-button reader, temperature sensors, etc.
  • Wide operating range from 8..36 VDC.
  • External power can be selectable enabled/disabled by the application.
  • On-board high-capacity Li-Ion battery.
  • Advanced power-management with wake-up on a wide range of events.
  • Hands-free interface with microphone and Class-D audio speaker amplifier.
  • High-speed USB programming cable support.
  • Fully supports the Professional Navigation and Messaging device PNM-220.
  • Support the Garmin Fleet Management Interface.
  • Fully supported by the VikMote Gateway 2 and the VikMote Deployment Server.
  • Accessories: Wi-Fi, Ethernet, Bluetooth, Camera and PNM-220 Navigation Device.
  • Exclusive and durable GOLD aluminum encapsulation.
  • Find out more and start developing today!

Platform Advantages

  • NX32 execution architecture.
  • Free VikMote Tools.
  • Programmable in VPL and Lua.
  • Huge standard API.
  • Comprehensive protocol support.
  • Full featured Device Simulator.
  • Sophisticated deployment tools.
  • Backward and forward compatible.

Deployment Features

  • Full Vikingegaarden / Upgrade & Deployment server compatible.
  • Upgrade of application, firmware and parameters over CSD, GPRS and Cable.
  • Upgrade can occur during full unit operation minimizing the impact on the customer.
  • Unattended and fully automatic upgrade and deployment.
  • Automatic ”bootstrap” of un-programmed unit on first time installation.

Cloud-based system

  • Web-based system with internet access from any PC, Mobile phone or tablet.
  • Modular system.
  • Own VMS domain.
    • Online setup.
    • Here-and-now status display.
    • Alarm List in real time.
    • Backup Settings.
    • No subscription - no binding.
    • Data usage per. year about 12-14 Mb.
  • Time stamps.
  • Multi user system.
  • Webservice.

High Performance

  • Based on the VikMote M2M Platform.
  • NX32 execution architecture.
    • VikMote tools with full featured device simulator.
    • Huge standard API with more than 800+ functions.
    • Comprehensive protocol support, including: TCP-UDP/IP, FTP, SMTP, RACP, MQTT, MODBUS, FMS/J1939, NMP/Garmin FMI.
    • Fully backward compatibility with existing X32 applications.
  • High-speed 3G/HSDPA GSM engine. Backward compatible with 2G/2.5G.
  • Internal and external SIM-card reader selectable from the application.
  • Digitized audio can be played over GSM or to an external device.
  • DTMF support for implementation of Interactive Voice Response applications.
  • State-of-the art Multi-GNSS positioning engine with GPS,GLONASS,QZSS.
  • High-performance 3-axis accelerometer with 16g scale.
  • Enhanced memory sub-system with fast program execution.
  • Huge data-flash/logger memory with a capacity of 8.5 MB.

VikMote VX20 Turbo+ specifikationer (only in English)

Processor and Main-memory

  • Powerful 32-bit ST ARM7 processor.
  • 2112 KB fast execution RAM.
  • 4532 KB Flash for firmware/application.

Storage

  • 7.5 MB persistent data flash.
  • 8 MB internal FAT32 flash drive.
  • 1 MB circular automatic datalogger.
  • 20 KB FRAM with fast access / unlimited write endurance.
  • SD-CARD reader with up to 32 GB.

GSM / HSDPA

  • Qualcomm QSC6270 single chip.
  • 3G / HSDPA with up to 3.6 Mbps.
  • UMTS / EDGE / GPRS support.
  • CSD with up to 64 Kbps.
  • SMS / PDU.
  • DTMF decoding / transmission.
  • Digitized voice playback / IVR.
  • eCall Accident / Emergency services.
  • Micro-SIM 1.8/3 volt.
  • External and internal SIM card-reader. Switchable from the application.

GNSS / GPS

  • Mediatek MT3333 Multi-GNSS chip.
  • GPS, GLONASS and QZSS.
  • 99 acquisition / 33 tracking channels.
  • SBAS (WAAS, EGNOS, MSAS, GAGAN).
  • Position update with up to 4 hz.
  • A-GPS capable.
  • Sensitivity. Tracking: -165 dBm Reacquisition: -160 dBm Cold start: -148 dBm.
  • Accuracy: < 2.5m CEP.
  • Anti-jamming, Noise cancellation.
  • Active 3 volt GNSS antenna.

Electrical Specification.

  • Operating voltage is 8 to 36 VDC.
  • Short and reverse power protected.

Battery and Charger

  • On-board 2Ah (nominal) Li-Ion battery.
  • Intelligent charger with temperature throttle and sub-zero degrees support.
  • On-board temperature sensor.

Digital/Analog Interface

  • 4 x digital solid-state digital output. Max. 36 volt / 1.5 A per. channel. Short-circuit, ESD, Inductive kick-back protected up to 20 mH.
  • 5 x digital inputs. Logic high: 8 to 40 VDC. Logic low: -5 to 3 VDC.
  • Digital input #5 can be used as ignition.
  • 2 x analog inputs. Range is 0..10V. Resolution: 12 bit Precision: ±1.5% FSR @ 25°C
  • Protected against transients and low-pass filtered.
  • Expandable I/O with MODBUS.

Communication

  • Full CAN2.0B with hardware filtering and multi-speed support.
  • 1 x RS232 with control signals.
  • 1 x RS232 with RX/TX. Alternatively used as service port.
  • 1 x RS485 with MODBUS support.
  • 1-Wire bus.

Power Management

  • 5 execution speeds.
  • Wait for Event: Timer, Digital input, RS232, CAN, GSM, Accelerometer and power change state.
  • Wait for event, from: 300 uA@12V.
  • Supervision of supply voltage.
  • Disable external power.

Accelerometer

  • 3-axis digital acceleormeter.
  • Resolution: 12 bit @ ±16g.
  • Low-power mode.

External Interfaces.

  • SIM-card slot for micro-SIM with lock and presence detection.
  • SD-CARD slot with presence and write protect detection.
  • Micro-jack 2.5” connector for hands-free.
  • Audio out for digitized voice playback.
  • 4 x LED indicators and 2 x DIP switches.
  • Reset/recovery switch, TE-Connectivity ”Mate’n’Lock’: RS232, I/O, Power, Communicaton.
  • RJ45 for RS232 with full control signals.
  • SMA Female connector for GSM.
  • SMB Female connector for GNSS/GPS.

Physical Characteristics

  • Encapsulation: Aluminum/plastic.
  • Optional mounting bracket.
  • W 97 x H 35 x D 132 mm. (without antenna connectors).

Environmental Specification

  • Operating temperature: -35 to 60°C.
  • Battery charge temperature: -10 to 45 °C
  • Recommended storage temperature: 0 to 45°C.
  • Humidity: 5..90% (non condensing).

Approvals

  • E1 type approval: 2004/104/EC UN ECE R10 - ed 3.
  • CE mark / Applied R&TTE directive.
  • GSM engine: CE/GCF/FCC/PTCRB.

Warranty

  • Two-years return to factory parts and labor.
  • Optional warranty up to 5 years. (restrictions apply).
Note: Some features are currently under development.

Om VikMote VX40i M2 PRO serienVikMpte VX40 Pro

  • Model til DIN-skinne montage
  • Fås som 2G og 3G
  • Fås med eller uden skærm
  • Kan anvendes til overvågning og fjernbetjening af processer over GSM-net og datafangst
  • Ideel til SCADA- og PLC-installationer

VikMote VX40i M2 PRO highlights (only in English)

Extensive Standard Features

  • Standard FAT32 SD-CARD reader with up to 32 GB capacity.
  • 2 x RS232 channels and 2 x RS485 channel.
  • 4 x analog inputs with 0..10 volt / 0..20 mA with 12 bit precision.
  • 4 x analog outputs with 0..10 volt / 0..20 mA.
  • 8 x digital inputs and 8 x high-power solid-state digital outputs.
  • Up to 4 digital inputs can be configured as IEC62053-31 Class A compliant.
  • Expandable I/O with standard MODBUS modules.
  • Full CAN 2.0B controller with hardware filtering and multi-speed support.
  • 1-Wire bus for accessories such as ID-button reader, temperature sensors, etc.
  • Wide operating range from 8..36 VDC.
  • On-board high-capacity Li-Ion battery.
  • Advanced power-management with wake-up on a wide range of events.
  • High-speed Mini-USB programming connector.
  • Housed in an industry standard M36 DIN compliant encapsulation.
  • Two-part pluggable connectors for easy installation and maintenance.
  • Fully supported by the VikMote Gateway 2 and the VikMote Deployment Server.
  • Accessories: MODBUS modules, Wi-Fi, Ethernet, Bluetooth and 2 MP camera.

High Performance

  • Based on the VikMote M2M Platform.
  • X32 execution architecture.
  • VikMote Tool with full featured device simulator.
  • Huge standard API with more than 800+ functions.
  • Comprehensive protocol support, including: TCP-UDP/IP, FTP, SMTP, RACP, MQTT, MODBUS.
  • World-wide Quad-band GSM engine.
  • Internal and external SIM-card reader.
  • Digitized audio can be played over GSM or to an external device.
  • DTMF support for implementation of Interactive Voice Response applications.
  • Graphical 144x32 pixels display with white-on-blue back-lit text/graphics.
  • Keypad with 8 keys for sophisticated user interaction and control.
  • Large data-flash/logger memory with a capacity of 4.5 MB.
  • Internal 4 MB FAT32 flash drive.

Cloud-based system

  • Web-based system with internet access from any PC, Mobile phone or tablet.
  • Modular system.
  • Own VMS domain.
    • Online setup.
    • Here-and-now status display.
    • Alarm List in real time.
    • Backup Settings.
    • No subscription - no binding.
    • Data usage per. year about 12-14 Mb.
  • Time stamps.
  • Multi user system.
  • Webservice.

Platform Advantages

  • NX32 execution architecture.
  • Free VikMote Tools.
  • Programmable in VPL and Lua.
  • Huge standard API.
  • Comprehensive protocol support.
  • Full featured Device Simulator.
  • Sophisticated deployment tools.
  • Backward and forward compatible.

VikMote VX40i M2 PRO specifikationer (only in English)

Processor & main-memory

  • Powerful 32-bit ST ARM7 processor.
  • 1088 KB fast execution RAM.
  • 2304 KB Flash for firmware/application.

Storage

  • 3.5 MB persistent data flash.
  • 4 MB internal FAT32 flash drive.
  • 1 MB circular automatic datalogger.
  • 8 KB FRAM with fast access / unlimited write endurance.
  • SD-CARD reader with up to 32 GB.

GSM/UMTS

  • VX40i M2 Pro+: Penta-band UMTS/HSPA. GSM: 850/900/1800/1900 MHz. UMTS: 800/850/900/1900/2100 Mhz. CSD with up to 14.4 Kbps.
  • VX40i M2 Pro: Quad-band GSM. 850/900/1800/1900 MHz. GPRS Class B, Multislot 12.
  • SMS / PDU.
  • DTMF decoding / transmission.
  • Digitized voice playback / IVR.
  • Mini-SIM 1.8/3 volt.
  • External SIM card-reader.
  • Optional Gemalto SIM-on-chip.

User interaction

  • 144x32 pixels graphical/text display. White-on-blue back-lit.
  • Keypad with 8 user defined keys.
  • Piezo Buzzer for user attention.
  • 3 x bi-colour LED.
  • Yellow status LED.
  • DIP-switches.
  • Reset / recovery switch.

Electrical specification

  • Operating voltage is 8 to 36 VDC.
  • Short and reverse power protected.

Battery and charger

  • On-board 2Ah (nominal) Li-Ion battery.
  • Intelligent charger with temperature throttle and sub-zero degrees support.
  • On-board temperature sensor.

Digital/analog interface

  • 8 x digital solid-state digital output. Max. 36 volt / 1.5 A per. channel. Short-circuit, ESD, Inductive kick-back protected up to 20 mH.
  • 8 x digital inputs. Logic high: 6 to 40 VDC. Logic low: -5 to 3 VDC.
  • 4 x IEC62053-31 Class A input.
  • Digital input #5 can be used as ignition.
  • 4 x analog inputs. Range is 0..10VDC or 0..20 mA Resolution: 12 bit Precision: ±1.5% FSR @ 25°C
  • 4 x analog outputs. Range is 0..10VDC or 0..20 mA Resolution: 10 bit Precision: ±1.5% FSR @ 25°C
  • Protected against transients and lowpass filtered.
  • Expandable I/O with MODBUS.

Communication

  • Full CAN2.0B with hardware filtering and multi-speed support.
  • 1 x RS232 with control signals.
  • 1 x RS485.
  • 1 x shared RS232 / RS485.
  • 1-Wire bus.

Power management

  • 5 execution speeds.
  • Wait for Event: Timer, Digital input, RS232, CAN, GSM, power change state.
  • Wait for event, from: 600 uA@12V.
  • Supervision of supply voltage/type.

External interfaces

  • SIM-card slot for micro-SIM with lock and presence detection.
  • SD-CARD slot with presence and write protect detection.
  • Audio out for digitized voice playback.
  • LED indicators and DIP switches.
  • Reset/recovery switch.
  • Two-part pluggable connector for: Power, I/O, RS485, 1Wire. CAN.
  • TE-Connectivity ”Mate’n’Lock’ for: RS232/DCOUT.
  • RJ45 for RS232 (EIA-561)
  • SMA Female connector for GSM.
  • Mini USB-B as service port.

Physical characteristics

  • Encapsulation:
  • 9 Module M36 DIN-rail.
  • Approx. 430 gram without accessories.
  • W 157 x H 86 x D 58 mm. (without SMA and screw-terminals).

Environmental specification

  • Operating temperature: -30 to 60°C.
  • Battery charge temperature: -10 to 45 °C
  • Recommended storage temperature: 0 to 45°C.
  • Humidity: 5..90% (non condensing).
  • Ingress Protection: IP20.

Approvals

  • EU EMC directive 2004/108/EU.
  • Applied R&TTE directive.
  • GSM engine: CE/GCF/FCC/PTCRB.

Warranty

  • Two-years return to factory parts and labor.
  • Optional warranty up to 5 years. (restrictions apply).
 Technical data are subject to changes.

Om VikMote VX40i STDVikMote VX40 STD

  • Model for DIN rail mounting.
  • Available with or without display.
  • Can be used for monitoring and remote control of processes of GSM networks and data capture.
  • Ideal for SCADA and PLC installations.

VikMote VX40i STD highlights (only in English)

Extensive Standard Features

  • 1 x RS232 channel / service port.
  • 5 x digital inputs and 3 x high-power solid-state digital outputs.
  • 2 x analog inputs with 0..10 volt / 0..20 mA.
  • 2 x analog outputs with 0..10 volt / 0..20 mA.
  • Up to 4 x digital inputs can be configured as IEC62053-31 Class A compliant.
  • Powerful on-demand hardware options: Digital I/O option: 8 x digital inputs and 8 x digital outputs (total). Analog I/O option: 4 x analog inputs and 4 x analog outputs (total). Communication option: RS485/MODBUS and 1-Wire bus support.
  • On-demand options can be applied anytime — even remotely after installation.
  • Expandable I/O with standard MODBUS modules.
  • 1-Wire for accessories such as ID-button reader, temperature sensors, etc.
  • Wide operating range from 8..36 VDC.
  • On-board Li-Ion battery.
  • Advanced power-management with wake-up on a wide range of events.
  • High-speed USB programming cable support.
  • Housed in an industry standard M36 DIN compliant encapsulation.
  • Two-part pluggable connectors for easy installation and maintenance.
  • Fully supported by the VikMote Gateway 2 and the VikMote Deployment Server.

High Performance

  • Based on the VikMote M2M Platform.
  • X32 execution architecture.
  • VikMote Tool with full featured device simulator.
  • Huge standard API with more than 800+ functions.
  • Comprehensive protocol support, including: TCP-UDP/IP, FTP, SMTP, RACP, MQTT, MODBUS.
  • World-wide Quad-band GSM engine.
  • Internal SIM-card reader.
  • Large data-flash/logger memory with a capacity of 4.5 MB.
  • Internal 4 MB FAT32 flash drive.

Cloud-based system

  • Web-based system with internet access from any PC, Mobile phone or tablet.
  • Modular system.
  • Own VMS domain.
  • Online setup.
  • Here-and-now status display.
  • Alarm List in real time.
  • Backup Settings.
  • No subscription - no binding.
  • Data usage per. year about 12-14 Mb.
  • Time stamps.
  • Multi user system.
  • Webservice.

 Platform Advantages

  • NX32 execution architecture.
  • Free VikMote Tools.
  • Programmable in VPL and Lua.
  • Huge standard API.
  • Comprehensive protocol support.
  • Full featured Device Simulator.
  • Sophisticated deployment tools.
  • Backward and forward compatible.

VikMote VX40i STD specifikationer (only in English)

Processor & main-memory

  • Powerful 32-bit ST ARM7 processor.
  • 1088 KB fast execution RAM.
  • 2304 KB Flash for firmware/application.

Storage

  • 3.5 MB persistent data flash.
  • 4 MB internal FAT32 flash drive.
  • 1 MB circular automatic datalogger.
  • 8 KB FRAM with fast access /unlimited write endurance.

GSM

  • Quad-band GSM engine. 850/900/1800/1900 MHz.
  • GPRS Class B, Multislot 10.
  • CSD with up to 19 Kbps.
  • SMS / PDU.
  • Micro-SIM 1.8/3 volt.
  • Internal SIM card-reader.
  • Optional Gemalto SIM-on-chip.

User interaction

  • 3 x bi-colour LED.
  • Yellow status LED.
  • Reset / recovery switch.

Electrical specification

  • Operating voltage is 8 to 36 VDC.
  • Short and reverse power protected.

Battery and charger

  • On-board 1Ah (nominal) Li-Ion battery.
  • Intelligent charger with temperature throttle and sub-zero degrees support.
  • On-board temperature sensor.

Digital/analog interface

  • Up to 8 x solid-state digital outputs. Max. 36 volt / 1.5 A per. channel. Short-circuit, ESD, Inductive kick-back protected up to 20 mH.
  • Up to 8 x digital inputs. Logic high: 6 to 40 VDC. Logic low: -5 to 3 VDC.
  • Digital input #5 can be used as ignition.
  • 4 x IEC62053-31 Class A input.
  • Up to 4 x analog inputs. Range is 0..10VDC or 0..20 mA Resolution: 10 bit Precision: ±1.5% FSR @ 25°C
  • Up to 4 x analog outputs. Range is 0..10VDC or 0..20 mA Resolution: 10 bit Precision: ±1.5% FSR @ 25°C
  • Protected against transients and lowpass filtered.
  • Expandable I/O with MODBUS.

Communication

  • 1 x RS232/service port.
  • 1 x RS485 (on-demand)
  • 1-Wire bus (on-demand)

Power management

  • 5 execution speeds.
  • Wait for Event: Timer, Digital input, RS232, GSM, power change state.
  • Wait for event, from: 600 uA@12V.
  • Supervision of supply voltage / type.

On-demand HW options

  • Applied ”any-time” - locally or remotely.
  • Over-the-air hardware upgrade.

Physical characteristics

  • Encapsulation: 9 Module M36 DIN-rail.
  • Approx. 330 gram without accessories.
  • W 157 x H 86 x D 58 mm. (without SMA and screw-terminals).

Environmental specification

  • Operating temperature: -30 to 60°C.
  • Battery charge temperature: -10 to 45 °C
  • Recommended storage temperature: 0 to 45°C.
  • Humidity: 5..90% (non condensing).
  • Ingress Protection: IP20.

Approvals

  • CE. EU EMC directive 2004/108/EU.
  • Applied R&TTE directive.
  • GSM engine: CE/GCF/FCC/PTCRB.

Warranty

  • Two-years return to factory parts and labor.
  • Optional warranty up to 5 years. (restrictions apply).

Om VikMote VX90 EncoreVikMote VX90

  • Vandtæt kasse, ideel til udendørs montage
  • Fås som standard med intern antenne med mulighed for eftermontering af ekstern antenne
  • Kan anvendes til overvågning og fjernbetjening af processer over GSM-net og datafangst
  • Fås som 3G-enhed og med indbygget Ethernet-port

VikMote VX90 Encore highlights (onlyin English)

Extensive Standard Features

  • RS232 channel with optional shared RS485 channel.
  • 2 x analog inputs with 0..10 volt / 0..20 mA with 12 bit precision.
  • 5 x digital inputs and 4 x high-power relays.
  • Up to 4 digital inputs can be configured as IEC62053-31 Class A compliant.
  • Expandable I/O with standard MODBUS modules.
  • 1-Wire bus for accessories such as ID-button reader, temperature sensors, etc.
  • Wide AC/DC power operating range from 100..260VAC / 8..36 VDC.
  • On-board Li-Ion battery.
  • 24 Volt DC-out capability for powering external equipment.
  • Advanced power-management with wake-up on a wide range of events.
  • High-speed mini-USB programming connector.
  • Housed in an ruggedized plastic encapsulation with cable glands.
  • IP65 water protected for outdoor usage.
  • Fully supported by the VikMote Gateway 2 and the VikMote Deployment Server..
  • Accessories: 1-wire accessories, MODBUS modules, etc.

Device Advantages

  • Quad-band GSM engine.
  • Internal/external antenna.
  • Digital and analog input/output.
  • AC/DC relay outputs.
  • RS232/RS485 channels.
  • MODBUS expandable I/O.
  • 1-Wire bus.
  • Digitized voice playback.
  • DTMF decoding/transmission.
  • Micro SD-CARD with up to 32 GB.
  • FAT32 file-system.
  • AC / DC powered.
  • Backup battery.
  • IP65 Ingress Protection
  • State of the art power-management.

High Performance

  • Based on the VikMote M2M Platform.
  • NX32 execution architecture.
  • VikMote tools with full featured device simulator.
  • Huge standard API with more than 800+ functions.
  • Comprehensive protocol support, including: TCP-UDP/IP, FTP, SMTP, RACP, MQTT, MODBUS.
  • Full backward-compatibility with existing X32 applications.
  • World-wide Quad-band GSM engine.
  • Internal and external GSM antenna connector. Selectable from application.
  • Internal SIM-card reader.
  • Digitized audio can be played over GSM.
  • DTMF support for implementation of Interactive Voice Response applications.
  • Enhanced memory sub-system with fast program execution.
  • Huge data-flash/logger memory with a capacity of 4.5 MB.
  • Internal 4 MB FAT32 flash drive.
  • Standard FAT32 SD-CARD reader with up to 32 GB capacity.

Cloud-based system

  • Web-based system with internet access from any PC, Mobile phone or tablet.
  • Modular system.
  • Own VMS domain.
    • Online setup.
    • Here-and-now status display.
    • Alarm List in real time.
    • Backup Settings.
    • No subscription - no binding.
    • Data usage per. year about 12-14 Mb.
  • Time stamps.
  • Multi user system.
  • Webservice.

Platform Advantages

  • NX32 execution architecture.
  • Free VikMote Tools.
  • Programmable in VPL and Lua.
  • Huge standard API.
  • Comprehensive protocol support.
  • Full featured Device Simulator.
  • Sophisticated deployment tools.
  • Backward and forward compatible.

VikMote VX90 Encore specifikationer (only in English)

Processor and Main-memory

  • Powerful 32-bit ST ARM7 processor.
  • 2112 KB fast execution RAM.
  • 4532 KB flash for firmware/application.

Storage

  • 4.5 MB persistent data flash.
  • 4 MB internal FAT32 flash drive.
  • 1 MB circular automatic datalogger.
  • 20 KB FRAM with fast access/unlimited write endurance.
  • SD-CARD reader with up to 32 GB.

GSM

  • 850/900/1800/1900 Mhz.
  • GPRS Multi-slot class 12.
  • Max. 85.6 kbps (up/down link)
  • CSD with up to 14.4 Kbps.
  • SMS / PDU.
  • DTMF decoding / transmission.
  • Digitized voice playback / IVR.
  • Mini-SIM 1.8/3 volt.
  • Internal SIM card-reader.
  • Internal GSM antenna.
  • External or internal antenna selectable by DIP-switch or user application
  • Optional Gemalto eSIM.

User Interaction

  • Three bi-colour LED/Yellow status.
  • DIP-switches.
  • Reset/recovery switch.
  • Antenna selection dip-switch.
  • Configuration jumpers.
  • Mini-USB for service port.

Battery and Charger

  • On-board 1Ah (nominal) Li-Ion battery.
  • Intelligent charger with temperature throttle and sub-zero degrees support.
  • On-board temperature sensor.

Digital/Analog Interface

  • 4 x relay output. Max. 5A @ 250VAC/30 VDC
  • 5 x digital inputs. Logic high: 6 to 40 VDC. Logic low: -5 to 3 VDC.
  • 4 x IEC62053-31 Class A input.
  • Digital input #5 can be used as ignition.
  • 2 x analog inputs. Range is 0..10VDC or 0..20 mA Resolution: 12 bit Precision: ±1.5% FSR @ 25°C
  • Protected against transients and lowpass filtered.
  • Expandable I/O with MODBUS.

Communication

  • RS232 channel.
  • On-demand: RS485 (shared).
  • 1-Wire bus.

Power Management

  • 5 execution speeds.
  • Wait for Event: Timer, Digital input, RS232, GSM, Power change state.
  • Wait for event, from: 600 uA@12V.
  • Supervision of supply voltage/type.

Electrical Specification

  • Supply operating range: 8 to 36 VDC. 100 to 260 VAC.
  • Short and reverse power protected.

Internal Interfaces

  • Screw-terminals for: Power, I/O and 24V DCOUT.
  • Angled screw-terminals for: RS232, RS485, 1-Wire.
  • Mini-USB for programming/service.

On-Demand Hardware Options

  • Applied ”any-time”- locally or remotely.
  • Over-the-air hardware upgrade.

External Interfaces

  • SMA Female connector for external GSM antenna.
  • 3 x PG11 cable glands.
  • 2 x PG9 blind plugs.

Physical Characteristics

  • Encapsulation: Durable Polycarbonate plastic.
  • Approx. 690 gram without accessories.
  • W 130 x H 180 x D 60 mm. (without SMA and PG connectors)

Environmental Specification

  • Operating temperature: -30 to 60°C.
  • Battery charge temperature: -10 to 45 °C
  • Recommended storage temperature: 0 to 45°C.
  • Humidity: 5..90% (non condensing).
  • Ingress Protection: IP65.

Approvals

  • R&TTE 1995/5/EC.
  • CE. EMC directive 2004/108/EU.
  • GSM engine: CE/GCF/FCC/PTCRB.

Warranty

  • Two-years return to factory parts and labor.
  • Optional warranty up to 5 years. (restrictions apply).

Om VikMote VX90 Turbo+VikMote VX90

  • Vandtæt kasse, ideel til udendørs montage
  • Fås som standard med intern antenne med mulighed for eftermontering af ekstern antenne
  • Anvendes til overvågning og fjernbetjening af processer over GSM-net og datafangst
  • Fås som 3G-enhed og med indbygget Ethernet-port

VikMote VX90 Turbo+ highlights (only in English)

Extensive Standard Features

  • Internal 8 MB FAT32 flash drive.
  • Standard FAT32 Micro SD-CARD reader with up to 32 GB capacity.
  • 2 x RS232 channels and 2 x RS485 channel.
  • 4 x analog inputs with 0..10 volt / 0..20 mA with 12 bit precision.
  • 4 x analog outputs with 0..10 volt / 0..20 mA.
  • 5 x digital inputs and 4 x high-power relays.
  • Up to 4 digital inputs can be configured as IEC62053-31 Class A compliant.
  • Expandable I/O with standard MODBUS modules.
  • 1-Wire bus for accessories such as ID-button reader, temperature sensors, etc.
  • Wide AC/DC power operating range from 100..260VAC / 8..36 VDC.
  • On-board high-capacity Li-Ion battery.
  • Advanced power-management with wake-up on a wide range of events.
  • High-speed USB programming connector.
  • Tntrusion detection.
  • Housed in an ruggedized plastic encapsulation with cable glands.
  • IP65 water protected for outdoor usage.
  • Fully supported by the VikMote Gateway 2 and the VikMote Deployment Server.

High Performance

  • Based on the VikMote M2M Platform.
  • NX32 execution architecture.
  • VikMote Tools with full featured device simulator.
  • Huge standard API with more than 800+ functions.
  • Comprehensive protocol support, including: TCP-UDP/IP, FTP, SMTP, RACP, MQTT, MODBUS, NMP/Garmin FMI.
  • Full backward-compatibility with existing X32 applications.
  • High-speed 3G/HSDPA GSM engine. Backward compatible with 2G/2.5G.
  • On-board Ethernet interface.
  • Medium range ISM band RF transceiver with on-board antenna.
  • Internal and external GSM antenna connector. Selectable from application.
  • Internal SIM-card reader.
  • Digitized audio can be played over GSM.
  • DTMF support for implementation of Interactive Voice Response applications.
  • Enhanced memory sub-system with fast program execution.
  • Huge data-flash/logger memory with a capacity of 8.5 MB.

Device Advantages

  • 3G/HSDPA GSM engine.
  • Internal/external antenna.
  • On-boad Ethernet interface.
  • Digital and analog input/output.
  • AC/DC relay outputs.
  • Multiple RS232/RS485 channels.
  • MODBUS expandable I/O.
  • 1-Wire bus.
  • ISM medium range RF.
  • Digitized voice playback.
  • DTMF decoding/transmission.
  • Large flash memory capacity.
  • Micro SD-CARD with up to 32 GB.
  • FAT32 file-system.
  • AC / DC powered.
  • High-capacity battery.
  • IP65 Ingress Protection

Cloud-based system

  • Web-based system with internet access from any PC, Mobile phone or tablet.
  • Modular system.
  • Own VMS domain.
    • Online setup.
    • Here-and-now status display.
    • Alarm List in real time.
    • Backup Settings.
    • No subscription - no binding.
    • Data usage per. year about 12-14 Mb.
  • Time stamps.
  • Multi user system.
  • Webservice.

Platform Advantages

  • NX32 execution architecture.
  • Free VikMote Tools.
  • Programmable in VPL and Lua.
  • Huge standard API.
  • Comprehensive protocol support.
  • Full featured Device Simulator.
  • Sophisticated deployment tools.
  • Backward and forward compatible.
  • Deployment Features • Full Vikingegaarden GPRS Gateway Professional / Upgrade & Deployment server compatible.
  • Upgrade of application, firmware and parameters over CSD, GPRS and Cable.
  • Upgrade can occur during full unit operation minimizing the impact on the customer.
  • Unattended and fully automatic upgrade and deployment.
  • Automatic ”bootstrap” of un-programmed unit on first time installation.

VikMote VX90 Turbo+ specifikationer (only in English)

Processor and Main-memory

  • Powerful 32-bit ST ARM7 processor.
  • 2112 KB fast execution RAM.
  • 4532 KB Flash for firmware/application.

Storage

  • 7.5 MB persistent data flash.
  • 8 MB internal FAT32 flash drive.
  • 1 MB circular automatic datalogger.
  • 20 KB FRAM with fast access /unlimited write endurance.
  • SD-CARD reader with up to 32 GB.

GSM

  • Qualcom QSC6270 single chip.
  • 3G / HSDPA with up to 3.6 Mbps.
  • UMTS / EDGE / GPRS support.
  • CSD with up to 64 Kbps.
  • SMS / PDU.
  • DTMF decoding / transmission.
  • Digitized voice playback / IVR.
  • eCall Accident / Emergency services.
  • Micro-SIM 1.8/3 volt.
  • Internal SIM card-reader.
  • Internal GSM antenna.
  • External or internal antenna selectable by DIP-switch or user application.
  • Optional Gemalto SIM-on-chip.

User Interaction

  • Three bi-colour LED / Yellow status.
  • DIP-switches.
  • Reset/recovery switch.
  • Antenna selection dip-switch.
  • Configuration jumpers.
  • Mini-USB for service port.
  • Intrusion-detection.

Electrical Specification

  • Supply operating range: 8 to 36 VDC. 100 to 260 VAC.
  • Short and reverse power protected.

Battery and Charger

  • On-board 2Ah (nominal) Li-Ion battery.
  • Intelligent charger with temperature throttle and sub-zero degrees support.
  • On-board temperature sensor.

Digital/Analog Interface

  • 4 x relay output. Max. 5A @ 250VAC / 30 VDC
  • 5 x digital inputs. Logic high: 6 to 40 VDC. Logic low: -5 to 3 VDC.
  • 4 x IEC62053-31 Class A input.
  • Digital input #5 can be used as ignition.
  • 4 x analog inputs. Range is 0..10VDC or 0..20 mA Resolution: 12 bit Precision: ±1.5% FSR @ 25°C
  • 4 x analog outputs. Range is 0..10VDC or 0..20 mA Resolution: 10 bit Precision: ±1.5% FSR @ 25°C
  • Protected against transients and lowpass filtered.
  • Expandable I/O with MODBUS.

Communication

  • 10BASE-T Ethernet inferface.
  • 1 x RS232 with control signals.
  • 1 x RS485.
  • 1 x shared RS232 / RS485.
  • 1-Wire bus.
  • On-board 868 Mhz ISM RF Up to 15 meter indoor / Up to 50 meter outdoor.
  • ISM RF can be disabled for world-wíde compliance requirements.

External Interfaces.

  • SMA Female connector for external GSM antenna.
  • 3 x PG11 cable glands.
  • 2 x PG9 blind plugs.

Power Management

  • 5 execution speeds.
  • Wait for Event: Timer, Digital input, RS232, GSM, Power change state, RF and Intrusion.
  • Wait for event, from: 600 uA@12V.
  • Supervision of supply voltage / type.

Internal Interfaces.

  • Screw-terminals for: Power, I/O and 12/24V DCOUT.
  • Angled screw-terminals for: RS232, RS485, 1-Wire and 3.3V DCOUT.
  • Mini-USB for programming/service.
  • Standard RJ45 Ethernet connector.

Physical Characteristics

  • Encapsulation: Durable Polycarbonate plastic.
  • Approx. 690 gram without accessories.
  • W 130 x H 180 x D 60 mm. (without SMA and PG connectors).

Environmental Specification

  • Operating temperature: -30 to 60°C.
  • Battery charge temperature: -10 to 45°C
  • Recommended storage temperature: 0 to 45°C.
  • Humidity: 5..90% (non condensing).
  • Ingress Protection: IP65.

Approvals

  • R&TTE 1995/5/EC.
  • CE. EMC directive 2004/108/EU.
  • GSM engine: CE/GCF/FCC/PTCRB.

Warranty

  • Two-years return to factory parts and labor.
  • Optional warranty up to 5 years. (restrictions apply).

Om VikMote SX10VikMote SX10

  • Vandtæt plastkasse
  • Stor intern batteribackup
  • Beregnet til langtids batteridrift, hvor der ikke findes spændingsforsyning
  • Kan anvendes til overvågning og fjernbetjening af processer over GSM-net

VikMote SX10 highlights (only in English)

Extensive Standard Features

  • 2 Digital inputs, 2 Digital output and 2 Analog inputs.
  • Dedicated high-speed USB programming port providing improved communication speed.
  • Standard RS232 serial port. Alternatively used as service port.
  • 1-wire bus for connection to temperature sensors, ID-button readers, etc.
  • Full support for the Navigation and Messaging Platform available from Logic IO.
  • One user available bi-color LED-Indicators with 3 colors: Green, Red and Yellow.
  • One bi-color and one yellow system LED indicating state of GSM, Power management and Battery charging etc.
  • High performance +/-16g 3-axis accelerometer / movement sensor.
  • On-board dipswitch for input configuration and general use. Temperature sensor.

Communication Technology

  • SX10 PRO: Quad Band (850/900/1800/1900 Mhz) GSM.
  • SX10 PRO-r: Triple Band (900/1800/1900 Mhz) GSM-R for GSM-Rail system.
    • SMS (Text and PDU)
    • GPRS. Multislot class 10
    • CSD (Datacall)
    • On-board internal chip antenna. Prepared for external antenna connection.
  • On-board high-sensitivity GPS-receiver with extremely fast acquisition and low-power consumption.
    • Full SBAS (EGNOS / WAAS / MSAS) support for enhanced GPS precision
    • Prepared for A-GPS.
    • On-board internal patch antenna. Prepared for external antenna connection.
  • On-Board medium range RF transceiver (868 MHz)
    • On-board internal chip antenna prepared for external antenna connection.

High Performance

  • Powerful industry leading dedicated 32-bit ARM7 Processor.
  • Very fast execution (48 MHz).
  • 1088 KByte RAM.
  • 2304 KByte Flash for application and database.
  • 512 Kbyte Dataflash for datalogging / parameters.
  • Support for additional 8 MByte DataFlash.
  • 512 Kbyte internal flash drive with FAT compatible file-system, for easy sharing of files with a PC.
  • 8 KByte FRAM for fast access memory without any write endurance limitations.
  • Micro-SD Card Reader with FAT32 file-system and up to 32 GB capacity.

Flexible Power

  • Powered from internal battery pack and/or from external powers source.
  • Several battery configurations supported:
    • 58 Ah (nominel) non-rechargeable battery. Height: 56 mm.
    • 24 Ah (nominel) non-rechargeable battery. Height: 43 mm.
    • 10 Ah (nominel) rechargeable battery. Height: 43 mm.
    • 2 Ah (nominel) rechargeable battery. Height: 43 mm.
  • Automatic switch-over from external to internal power.
  • Automatic charging and maintenance of rechargeable battteries.
  • Integrated dynamic battery power consumption measurement circuit for management and statistical purposes.
  • During service and development the unit is powered directly from USB.
  • Development Tools
  • Programmable using the VikMote Tool full-feature development environment.
  • Easy to learn VPL high-level programming language based on the EIC 1131-3 industrial standard.
  • More than 800+ standard functions and 1000 pages of on-line documentation suits every application.
  • Many example programs available to ”kick-start” application development.
  • Full feature Microsoft Windows Simulator allowing test of complete application without use of physical unit.
  • VSMS technology seamlessly supports SMS, GPRS, CSD without application/server changes.
  • Seamless upgrade to future technologies.

Cloud-based system

  • Web-based system with internet access from any PC, Mobile phone or tablet.
  • Modular system.
  • Own VMS domain.
    • Online setup.
    • Here-and-now status display.
    • Alarm List in real time.
    • Backup Settings.
    • No subscription - no binding.
    • Data usage per. year about 12-14 Mb.
  • Time stamps.
  • Multi user system.
  • Webservice.

Advanced Power Management

  • Several power-saving modes: Zero Power, ’Wait for Event’, zero-power and 5 processor execution steps.
  • Wakeup from ’Wait for Event’ using: Digital input, 3D movement sensor, Timeout, GSM- or UART activity.
  • Advanced power saving mode while awaiting 2D/3D GPS fix.
  • Zero Power saving mode reducing the power consumption to virtually none with wake-up from:
    • 3D movement sensor.
    • Digital inputs.
    • Timer.
  • Integrated dynamic battery power consumption measurement circuit for management and statistical purposes.

Deployment Features

  • Full Vikingegaarden GPRS Gateway Professional / Upgrade & Deployment server compatible.
  • Upgrade of application, firmware and parameters over CSD, GPRS and Cable.
  • Upgrade can occur during full unit operation minimizing the impact on the customer.
  • Unattended and fully automatic upgrade and deployment.
  • Automatic ”bootstrap” of un-programmed unit on first time installation.

VikMote SX10 specifications

VikMoteSX10 specifications

Sammenlign VikMote-enhederne

Få et komplet overblik over alle VikMote-enheder

VX10+  VX10+/C VX20ENCORE VX20TURBO VX20TURBO+ VX40iSTD VX40iM2 PRO VX40iM2 PRO+ VX90ENCORE VX90TURBO+ SX10PRO
Indbygget Ethernet:
- - - - - - - - - -
UMTS / HSPA motor (3G):
- - - - - -
Verdensomspændende Quad Band GSM-motor (2G):
- - - - -
RF ISM Kommunikation (868 Mhz):
- - - - - - -
GNSS modtager med GPS / GLONASS / QZSS:
- - - - - -
SuperGPS:
- - - - -
Dual GSM-antenne (intern/ekstern):
- - - - - - - -
Antal digital indgange:
2 2 5 5 5 5 8 8 5 5 2
Antal digital udgange (Solid State):
2 2 4 4 4 3 8 8 - - 2
Antal digital udgange (relæer):
- - - - - - - - 4 4 -
Antal analog indgange:
1 1 2 2 2 2 4 4 2 4 2
Antal analog udgange:
- - - - - - 4 4 - 4 -
IEC62053-31 input support (S0):
- - - - - -
I/O kan udvides med MODBUS-moduler:
- - -
1-Wire support (iButton, Temperaturfølere osv):
-
Vibration sensor:
- - - - -
Avanceret 3D G-Sensor:
- - - - -
Antal RS232-kanaler:
1 - 1 2 2 1 2 2 1 2 1
Antal dedikerede RS485-kanaler:
- - 1 1 1 1 1 1 - 1 -
Antal RS485-kanaler (delt med RS232):
- - - - - - 1 1 1 1 -
Full CAN 2.0B Controller:
- - - - -
Internt batteri back-up (nominel):
Zero-power tilstand:
- - - - - - - - - -
Grafisk LCD-display med betjening:
- - - - - - - - -